Beckhoff CX-B510 Series Скачать руководство пользователя страница 46

Страница: 46 / 81

Parameterization and commissioning

CXxxxx-M510/B510

Version: 1.0

5.2.3

Creating a virtual slave

Additional virtual slaves can be created on the same hardware interface. This enables more data to be
exchanged with a CANopen master, or a connection with a second CANopen master can be established.

Each virtual slave is assigned a dedicated address via TwinCAT and is configured like an independent
device for the CANopen master.

Prerequisites for this step:

• A CANopen slave, created in TwinCAT.

Create a virtual slave as follows:

1. Right-click on a CANopen slave in the tree view on the left.

2. Click on

Append Box

in the context menu.

A further box (virtual slave) is created.

Variables for the virtual slave can now be created. In the next step you can set the address for the slave.

Содержание CX-B510 Series


















































































Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды

Beckhoff CX-B510 Series, Руководство пользователя

Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды