Beckhoff CX-B510 Series Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 81

background image

Connection and cabling

CXxxxx-M510/B510

29

Version: 1.0

• CSA AWM I/II A/B 80°C 300V FT1

• corresponds to the DeviceNet "Thin Cable" specification

Shielding

The screen is to be connected over the entire length of the bus cable, and only galvanically grounded at one
point, in order to avoid ground loops.
The design of the screening, in which HF interference is diverted through R/C elements to the mounting rail
assumes that the rail is appropriately earthed and free from interference. If this is not the case, it is possible
that HF interference will be transmitted from the mounting rail to the screen of the bus cable. In that case the
screen should not be attached to the couplers - it should nevertheless still be fully connected through.

Cable colors

Recommended application of Beckhoff CAN cables:

Function

ZB5100 cable color

ZB5200 cable color

CAN Ground

black/

(red)

black

CAN Low

black

blue

Shield

Filler strand

Filler strand

CAN high

white

white

not used

(red)

(red)

«
...
27
28
29
30
31
...
»

Содержание CX-B510 Series


















































































Отзывы:

Нет отзывов

Похожие инструкции для CX-B510 Series

Бренд: ICS ELECTRONICS Страницы: 6

AJSPD850P - P2 DECK

Бренд: Panasonic Страницы: 73

Бренд: IBEX Страницы: 4

Бренд: Latham Страницы: 4

Бренд: SafeWaze Страницы: 23

Бренд: WalkMed Страницы: 2

Бренд: Walinga Страницы: 20

Бренд: Phenix Technologies Страницы: 39

Бренд: Triton Страницы: 31

IMPULSE 2 IT8026 Glute Master

Бренд: BM FITNESS Страницы: 18

Бренд: Pixlip Страницы: 15

AtLite Sure-Lites SELDWA29SD

Бренд: Eaton Страницы: 4

Бренд: Xils lab Страницы: 31

Бренд: Car Solutions Страницы: 24

Бренд: Omni Страницы: 20

Combination EC Series

Бренд: Eastey Страницы: 81

Бренд: JK Audio Страницы: 20

Бренд: Launch Страницы: 81

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды