Beckhoff CX-B510 Series Скачать руководство пользователя страница 52

Страница: 52 / 81

Parameterization and commissioning

CXxxxx-M510/B510

Version: 1.0

Adding a PLC project

The PLC project can be added in the System Manager. The newly created variables from a PLC project are
integrated in the System Manager and can be linked with the inputs and outputs of the hardware.

Prerequisites for this step:

• An Embedded PC, added in TwinCAT.

• A correctly compiled PLC project and a .tpy file.

Proceed as follows:

1. Switch back to the System Manager window.

2. Right-click on

PLC – Configuration

in the tree view on the left.

3. In the context menu click on

Append PLC Project

4. Select a file with the extension .tpy in your system directory and confirm with

The PLC project is added in the tree view under PLC – Configuration. The variables defined in the
project are shown under the inputs and outputs.

In the next step you can link the variables with the hardware.

Содержание CX-B510 Series


















































































Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды

Beckhoff CX-B510 Series, Руководство пользователя

Результаты поиска

Содержание CX-B510 Series

Отзывы:

Похожие инструкции для CX-B510 Series

Бренды по названию

Популярные бренды