Basler BE1-50/51B-214 Скачать руководство пользователя страница 19

Страница: 19 / 70

9252000994 Rev N

BE1-50/51B-214/-215/-223/-225 General Information

1-9

Qualified to IEEE C37.90.1-1989

Standard Surge Withstand Capability (SWC) Tests for Protective Relays

and Relay Systems.

Surge Withstand Capability

Qualified to IEC 255-5.

Impulse

Field-tested using a 5-watt, hand-held transceiver operating at random frequencies centered around 144
MHz and 440 MHz, with the antenna located 6 inches from the relay in both horizontal and vertical
planes.

Radio Frequency Interference (RFI)

Withstands 2 G in each of three mutually perpendicular planes swept over the range of 10 to 500 Hz for a
total of 6 sweeps, 15 minutes each sweep.

Vibration

Withstands 15 G in each of three mutually perpendicular planes.

Shock

Environment

Operating Temperature:

–

C to 70

C (

–

F to158

Storage Temperature:

–

C to 70

C (

–

F to 158

F).

Agency Recognition

GOST-R certified per the relevant standards of Gosstandart of Russia.

GOST-R Certification

Physical

Weight:

6.1 lb (2.77 kg)

Содержание BE1-50/51B-214







































































Результаты поиска

Содержание BE1-50/51B-214

Отзывы:

Похожие инструкции для BE1-50/51B-214

Бренды по названию

Популярные бренды

Basler BE1-50/51B-214, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-50/51B-214

Отзывы:

Похожие инструкции для BE1-50/51B-214

Бренды по названию

Популярные бренды