Basler BE1-50/51B-214 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 70

background image

9252000994 Rev N

BE1-50/51B-214/-215/-223/-225 General Information

1-1

SECTION 1

•

GENERAL INFORMATION

INTRODUCTION

BE1-50/51B-214/-215/-223/-225 protective relays are direct replacements for General Electric, IAC relays.
The BE1-50/51B-214/-215/-223 has a 5 ampere current sensing input. The BE1-50/51B-225 has a 1
ampere current sensing input. Compatible IAC model numbers are listed in Table 1-1.

Table 1-1. GE IAC Relays Suitable For Direct Replacement

IAC Model Number

Curve Type

12IAC51A

∗∗∗

A

Inverse

12IAC51B

∗∗∗

A

Inverse with Instantaneous

12IAC53A

∗∗∗

A

Very Inverse

12IAC53B

∗∗∗

A

Very Inverse with Instantaneous

12IAC55A

∗∗∗

A

Short Time

12IAC55B

∗∗∗

A

Short Time with Instantaneous

12IAC66A

∗∗

A

Long Time

12IAC66B

∗∗

A

Long Time with Instantaneous

12IAC77A

∗∗∗

A

Extremely Inverse

12IAC77B

∗∗∗

A

Extremely Inverse with Instantaneous

∗

Any digit covering all pickup ranges and 50 Hz or 60 Hz models.

To replace an existing IAC relay, perform the following steps.

1.  Select the desired relay settings on your new BE1-50/51B-214/-215/-223/-225 relay.
2.  Remove the existing IAC relay.
3.  Attach the cover adapter to the existing case.
4.  Insert the new relay.
5.  Reinstall the existing connection plug.
6.  Install the new Basler Electric cover.

Basler Electric BE1-50/51B-214/-215/-223/-225 protective relays are self-powered, microprocessor-
based, non-directional phase or ground relays that monitor the magnitude of a single-phase ac current to
provide accurate instantaneous and time overcurrent protection for 50 Hz or 60 Hz power systems. Each
model covers 10 popular time characteristics and a wide range of pickup settings.

FEATURES

A wide range of pickup settings and front panel selectable time characteristics permit applications
involving coordination with fuses, reclosers, cold load pickup, motor starting, and fixed time requirements.
Also, an integrating reset function is available to simulate the disk reset of electromechanical relays.

BE1-50/51B-214/-215/-223/-225 overcurrent relays have the following standard features.

•

Independent time and instantaneous elements

•

A secure method to manually trip the breaker at the relay front panel

•

Direct reading front panel controls

•

Minimum pickup setting for safety during installation

•

Time characteristics extend to a pickup multiple of 40

•

Rugged draw-out construction with steel case

•

Gravity latching targets retain indication without power

•

Built-in accuracy eliminates internal adjustments

•

Minimum transient overreach

•

Field selectable characteristic curve selection similar to either GE IAC or ABB type curves

•

Field selectable instantaneous or integrating reset

•

Field selectable 50 or 60 Hz operation

•

Field selectable 0.0 or 0.1 second, fixed, instantaneous delay

«
...
9
10
11
12
13
...
»

Содержание BE1-50/51B-214







































































Отзывы:

Нет отзывов

Похожие инструкции для BE1-50/51B-214

Cutler-Hammer FP-5000

Бренд: Eaton Страницы: 213

Бренд: Zamel Страницы: 2

Бренд: Eaton Страницы: 187

Бренд: ZIEHL Страницы: 28

440R-S845AER-NNL

Бренд: Rockwell Automation Страницы: 8

Бренд: ZIEHL Страницы: 8

Бренд: ZIEHL Страницы: 8

Бренд: Schweitzer Engineering Laboratories Страницы: 204

Бренд: Schweitzer Engineering Laboratories Страницы: 208

Бренд: RMS Страницы: 40

Бренд: MULTISPAN Страницы: 4

Бренд: Danfoss Страницы: 44

CIRCUIT SHIELD 49/50/51

Бренд: ABB Страницы: 14

Бренд: ABB Страницы: 24

Cutler-Hammer CEP7 Series

Бренд: Eaton Страницы: 4

Бренд: ZIEHL Страницы: 8

RadioLink ScenePoint RDR Series

Бренд: Vantage Hearth Страницы: 4

Бренд: SafeTrust Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды