background image

A-5

Vegetables  are  generally  easy  to  cook  on  the  grill.  The
Secondary Cooking Rack makes it convenient because you
can still use the main cooking area while the vegetables are
suspended above the grids.

Pre-cook hard vegetables by briefly boiling or microwaving
them before cooking on the grill. Wrap vegetables in a double
thickness of foil to protect them while cooking on the grill.
Then, remove the foil if desired, 10-15 minutes before the
end of cooking, brush vegetables with butter or oil and finish
cooking.

Guide to Using the Secondary Cooking Rack

The Secondary Cooking Rack can be used for purposes
other than just the obvious. Consider using the rack for
warming French bread, garlic bread, croissants or even
bagels.

A small whole fish wrapped in foil also cooks well on the
Secondary  Cooking  Rack.  Parcels  of  seafood  such  as
scallops, prawns and sliced fish fillets prepared in a sauce
and portioned into small foil wraps cook well this way, too.

Slow Cooking with a Rotisserie

Rotisserie cooking produces foods that are moist, flavor-
ful  and  attractive.  The  rotisserie  system  is  most  com-
monly used for cooking meat or poultry and is designed
to cook food slowly.

The cooking times on a rotisserie will be approximately the
same as for oven cooking.

Balancing the Food

In  rotisserie  cooking,  balancing  the  food  is  of  utmost
importance. The rotisserie must turn evenly or the stop-
ping  and  starting  action  will  cause  the  food  to  cook
unevenly and possibly burn the heavier side.

The easiest foods to balance are those of uniform shape
and texture. To test if the food is balanced correctly when
secured, place the ends of the rotisserie spit loosely in the
palms of your hands. If there is no tendency to roll, give the
spit a quarter turn. If it is still stable, give it a final quarter
turn. It should rest without turning in each of these posi-
tions. It can then be attached to your grill.

Food Preparation

When preparing poultry, truss the birds tightly so that wings
and drumsticks are close to the body of the bird. The cavity of
the bird may be stuffed prior to this. Pull the neck skin down
and, using a small skewer, fix it to the back of the bird. Push
the rotisserie spit through lengthwise, catching the bird in the
fork of the wishbone. Center the bird and tighten with the
holding forks. Test the balance as described before.

A rolled piece of meat requires the rotisserie skewer to be
inserted through the center of the length of meat, then se-
cured and balanced.

For meats that contain bones, it is best to secure the rotis-
serie skewer diagonally through the meaty sections. If pro-
truding bones or wings brown too quickly, cover with pieces
of foil.

Guide to Rotisserie Cooking

Preparing to Smoke

Smoking gives food a distinctive, delicious flavor. You will find
a variety of wood chips available for use in smoking grilled
foods. Pre-soaking of wood chips may be required so read
and follow the manufacturer's  instructions for preparing
smoking chips prior to use.

Note:

 It is our experience that many smoking chip products

do not actually produce a smoke but instead infuses the
food with flavor. Please read product labels carefully and if
in doubt, ask your retailer for details.

Using A Smoker Box

There  are  many  optional  smoker  boxes  available  for
purchase. Follow these guidelines and always refer to the
label of your smoking chips for specific directions.

Raise your Grill Lid and light the grill. Lower the Grill Lid
allowing your grill to reach the desired cooking tempera-
ture for the food you are grilling. Fill your smoker box with
your prepared smoking chips. Dried herbs and spices may
also be added to produce different flavors. Wear a flame
retardant BBQ Mitt and place your smoker box on a Cook-
ing Grid or Flame Tamer directly above a lit grill Burner. The
heated smoking chips will flavor your foods.

Tips for Smoking

You can reduce the strength of the smoke flavor by only
smoking for half or three quarters of the cooking time. The
heat required for smoking is normally LOW to MEDIUM.

Foods naturally high in oils lend themselves well to smok-
ing, while drier foods benefit from a marinade.

Guide to Smoking




Tuna steaks,

 marinated in Asian flavors of sesame

oil, soy sauce and sherry.

Pork fillets,

 rubbed with ginger, orange rind and

brushed with maple syrup.

Mussels,

 brushed with lemon rind and chili oil.

Lamb cutlets,

 marinated in virgin olive oil, lemon,

oregano and black pepper. The same marinade can
be used for a whole leg or rack of lamb.

Chicken, 

boneless chicken pieces

especially sliced

breasts.

Fish, 

sliced fillets of firm fish, assorted seafood such

as prawns, scallops and calamari.

Pork, 

sliced fillets, diced or minced pork, sliced leg

steak, sliced chops.

Beef, 

sliced fillet, rib-eye, round, rump, sirloin.

Lamb, 

sliced fillet, round, loin.

Содержание Grand Turbo B4019LP



































Отзывы: