background image

Installation  Instruction

Combustible  Clearance

Island  Contstruction

Liquid  Propane(LP)  Ventilation

Island  /  Grill  Placement

It  is  required  that  the
interior  of  the  island/
structure  to  be  built
hollow  and  with  proper
ventilation  based  on  gas
type(see  below  images
for  ventilation).  Being
hollow  allows  the  proper
air  flow  for  the  BBQ
Unit  to  both  breath  and
fuction  properly,  and
vent  correctly(based  on
the  ga  s  type).

Natural  Gas  (NG)  Ventilation

36"

36"

36"

36"

BBQ  Grills  are
required  to  be  36

away  from  any
combustible
material  in  all
directions.  Failure
to  do  so  could
lead  to  the  damage  of
the  island/structure,  the
surrounding  components  and
area,  and  the  BBQ  grill  itself.

NOTE:  Island/structure  should  not  be  built
out  of  any  type  of  combustible  material.

Ventilation  is
required  to  be
along  the  bottom
of  the  island/
structure  for  LP
units  due  to  LP
Gas  weighs  more
than  air.  This  will
ensure  proper  gas
ventilation  in  the  case  of  a  gas
leak.  This  will  also  allow  for  proper
air  flow  of  LP  units

.

NOTE: Access  doors  are  not  considered
proper  ventilation.

Ventilation is
required to  be
along  the  top  of
the island/
structure for  NG
units  due  to  NG
Gas weighs less
than air. This will
ensure proper gas
ventilation in  the  case  of  a  gas
leak. This will also allow for proper
air  flow of  NG  units

.

NOTE: Access  doors  are  not  considered
proper  ventilation.

It  is  suggested
that  when  designing
and  placing
the  BBQ  Grill,
island/  structure
that  it  is
placed/built  facing
the  wind  (if  the
island/structure  is  located
in  a  high  wind  area).

If  this  is  an  unavoidable  situation  it  is
suggested  to  build  a  backsplash  on  the  island/
structure  to  help  divert/prevent  wind  from
entering  the  rear  of  the  BBQ  unit.

Note:  these  guidelines  will  be  considered  if  there  is
any  warranty  request  submitted  by  the
customer.  Not  following  these  guidelines  can  result
in  the  grill  not  functioning  correctly  and  can  lead  to
voiding  the  warranty  on  specific  parts  based  on  the
issue  that  arises.

Grand  Home  Holdings  /  Barbeques  Galore  are  not
liable  for  any  3rd  party  construction  or  installation  of
its  products.  Grand  Home  Holdings  /  Barbeques
Galore  can  decline 

service

  and  or 

warranty

  of

parts  for  the  product  if  the  above  installation/
construction  guidelines  are not  followed.  Grand
Home  Holdings  /  Barbeques  Galore  may  request
photos  of  the  installation/construction  if  a  warranty
claim  is  placed  to  verify  proper  installation  of  the
product.

!

!

 WARNING

13

Содержание Grand Turbo B4019LP



































Отзывы: