background image

Table  of  Contents

Primary  Safety  Warnings............................1-3
Pre-Assembly  Instructions...............................3
Part  Diagrams  and  Lists............................4-8
Assembly  Instructions.................................9-12
Use  &  Care  Instructions:

  Gas  Safety  and  Leak  Tests..............13-17

 

Natural  Gas  Connection............................18

  Lighting  Instructions...............................19-20

  Troubleshooting...........................................21

  Rotisserie  Instruction ........................... ..22-24

Cleaning  and  Maintenance .................... ..25-26
Cooking  Guide ........................................ ..A1-A5
Frequently  Asked  Questions ................. ..A6-A7
Warranty...........................................Back  Cover

2

Do  not store or use gasoline or other
flammable liquids or vapors in the
vi c i n i ty  o f   t h i s   o r   an y  o t h e r
appliances.
An LP  cylinder not connected for
use shall not be stored in the vicinity
of this or any other appliance.

1.

2.

LPG  models  must  be  used  with  Liquid  Propane
Gas  and  the  regulator  assembly  supplied.  Natural
Gas  models  must  be  used  with  Natural  Gas  only.
Any  attempt  to  convert  the  grill  from  one  fuel  type
to another is extremely hazardous  and will void the
warranty.

Keep  gas  regulator  hose  away  from  hot  grill  sur-
faces and dripping grease. Avoid unnecessary twist-
ing  of hose. Visually inspect  hose prior to each use
for  cuts,  cracks,  excessive  wear  or  other  damage.
If  the  hose  appears  damaged  do  not  use  the  gas
grill.  Call  1-800-474-5587  for  a  certified  replace-
ment  hose.

California Proposition 65

Combustion  byproducts  produced  when  using  this
product contain chemicals known to the State of Cali-
fornia to cause cancer, birth defects, or other reproduc-
tive harm.

Brass components on the grill, such as hose fittings,
propane cylinder valves (sold separately) and burner
valve stems, contain lead which is known to the State
of California to cause cancer, birth defects, or other
reproductive harm.

Never use charcoal

 or lighter fluid in this gas grill.

Failure to comply with these instructions could result
in a grease fire or explosion that could cause serious
bodily injury, death or property damage.

Before each use of your grill:

 Inspect the Grease Tray,

Grease Tray Heat Shield and inside of the Grill Bowl to
be  sure  there  is  no  excessive  grease  and  debris
buildup. Clean the Grease Tray, Grease Tray Heat
Shield and inside of the Grill Bowl frequently to elimi-
nate grease/debris build-up and to prevent grease
fires. 

Failure to comply with these instructions could

result in a grease fire and even a subsequent explo-
sion that could cause serious bodily injury, death or
property damage.

!

This  appliance,  when  installed,  must  be  electri-
cally  grounded  in  accordance  with  local  codes
or,  in  the  absence  of  local  codes,  with  the

National Electrical Code,  ANSI/NFPA  70, 

or  the

Canadian  Electrical  Code,  CSA  C22.1.

Keep  any  electrical  supply  cord  and  the  fuel
supply  hose  away  from  any  heated  surfaces.

  WARNING

!

  DANGER

!

!

1.
2.
3.
4.

If  you  smell  gas:

Shut  off  gas  to  the  appliance.
Extinguish  any  open  flame.
Open lid.
If  odor  continues,  keep  away  from
the  appliance  and  immediately  call
your  gas  supplier  or  your  fire
department.

WARNING

!

!

WARNING

!

!

Never 

cover  or  wrap  the  Cooking  Grids,  bottom

of  the  Grill  Bowl,  Grease  Tray  with  aluminum  foil
or  any  other  material  that  will  absorb  grease.

!

!

 WARNING

Содержание Grand Turbo B4019LP



































Отзывы: