background image

USE  AND  CARE  INSTRUCTIONS

19

5.

8.

7.

9.

6.

Set Control Knobs to OFF and open the LP Gas tank valve

SLOWLY 1/4 of a turn

.  For Natural Gas open the Shut Off

Valve at source.

Push and turn Right Main Burner Control Knob to Ingitor/HI.
You will hear a clicking sound as the burner is being ignited.
Always light the RIGHT Main Burner first.

If  ignition  does  not  occur  in  5  seconds,  turn  the  Burner
Control(s)  off,  wait  5  minutes,  and  repeat  the  lighting
procedure. If ignition still does not occur, turn the burner
control(s) and gas source OFF. Wait 5 minutes for gas to
clear and then conduct a leak test of ALL gas connections
and gas sources as explained in the Use and Care section
of this manual. If no leaks are detected, wait 5 minutes for
any gas to clear and repeat the lighting procedure.

After one Burner is lit, turn the tank valve SLOWLY one
more 1/4 of a turn.

Turn each other burner knob to 

Ingitor/HI

 to light. Note:

When lighting all main burners, start with the burner fur-
thest from fuel source location, then light remaining burn-
ers in sequence moving toward fuel source.

Failure  to  replace  a  faulty  hose,  secure  gas  supply
connections  or  to  open  the  Lid  before  proceeding  to
the  Lighting  Procedures  could  result  in  a  fire  or
explosion  that  could  cause  serious  bodily  injury,
death,  or  property  damage.

  WARNING

!

!

Grill Lighting Instructions

1.

Main Burner

Rotisserie
Burner

Infrared
Burner

Open  LP  Gas  tank

OFF

Ingitor/HI

LO

Rotisserie  Burner  Lighting  Instructions

Follow steps 1 through 5 of the Grill Lighting Instruc-
tions.

Push and turn Control Knob to Ingitor/HI and hold
knob in.

Keep pressing and hold in 5 - 10 seconds before
releasing.

If ignition does not occur in 5 seconds, turn the Burner
Control(s) off, wait 5 minutes, and repeat the lighting
procedure.  If  ignition  still  does  not  occur,  turn  the
burner control(s) and gas source OFF. Wait 5 minutes
for gas to clear and then conduct a leak test of ALL gas
connections and gas sources as explained in the Use
and  Care  section  of  this  manual.  If  no  leaks  are
detected,  wait  5  minutes  for  any  gas  to  clear  and
repeat the lighting procedure.

After Burner is lit, turn the tank valve SLOWLY one more
1/4 of a turn.

IMPORTANT: 

 Do not use the Rotisserie Burner and Main

Burners at the same time. Rotisserie burner is for Rotis-
serie Cooking only.

1.

2.

4.

3.

5.

Before each use, check all hoses for cracks, nicks, cuts,
burns or abrasions. If a hose is damaged in any way, do
not  use  your  grill  before replacing  the  hose  with  an
authorized part from the Parts List. Also make sure all
gas supply connections are securely tightened.
Familiarize  yourself with all Safety and  Use and Care
instructions  in  this  manual.  Do  not  smoke  while
lighting  your  grill  or  when  checking  the  gas  supply
connections.
Be  sure  that  the  LP  Gas  tank  is  filled,  and  lock
Casters  (if  the  grill  is  a  cart  model)  to  prevent
movement  during  grill  operation.
Open the Grill Lid.

4.

3.

2.

OFF

LO

Ingitor/HI

OFF

Ingitor/HI

Содержание Grand Turbo B4019LP



































Отзывы: