Barbeques Galore Grand Turbo B4019LP Скачать руководство пользователя | Manualshive

Страница: 10 / 34

background image

10

3

Install NG Regulator

Install the NG Regulator to the Manifold Extension Fitting and tighten securely.

Proper ventilation must be added to the island.

Pan  Head  Screw
3/16"x3/8"
Qty.  5
Part#  S182G03061

Install Regulator, Tank Tray Set and Liquid Propane(LP) Gas Tank

4

5/8" UNF male
thread

stainless steel flexible connec-
tor

(Not provided) must compy with the

Standard for connectors for Outdoor Gas
Appliances and Manufactured Homes,
ANSI Z21.75

•

CSA 6.27, and suitable for

outside installation.
The maximum length of the connection
shall be 6ft.(1.82m).

NOTE:  To  comply  with  the  standarad,  a  built-in  appliance  for  use  with  a  remote  self-contained  LP
gas  supply  system  must  use  rigid  pipe,semi-rigid  pipe  or  a  connector  complying  with  the  Standard
for  Connectors  for  Gas  Appliances,  ANSI  Z21.24/CSA  6.10,  or  the  Standard  for  Connectors  for
Outdoor  Gas  Appliances  and  Manufactured  Homes,  ANSI  Z21.75/CSA  6.27  to  connect  the  appliance
to  the  remote  self-contained  gas  supply  system.  For  safety  consideration,  we  suggest  to  use  a
stainless  steel  flexible  connector  as  shown.  But,  if  using  semi-rigid  tubing,  do  not  use  materials
made  of  aluminum  or  aluminum  alloy  tubing.  The  connector  should  be  installed  at  the  location
visible  when  opening  the  door.
On  the  proper  location,  drill  2  holes  on  the  island  left  side  panel  for  installing  the  regulator  bracket.  Then
install  the  regulator  using  2  Pan  Head  Screws  3/16"x3/8"  and  tighten  securely.
On  the  proper  location,  drill  3  holes  on  the  island  left  bottom  panel  for  installing  the  tank  tray  set.  Then
install  tank  tray  set  using  3  Pan  Head  Screws  3/16"x3/8"  and  tighten  securely.
Connect  the  stainless  steel  flexible  connector  to  the  manifold  and  regulator,  then  use  a  clamp  to  hold
the  stainless  steel  flexible  connector  as  shown  for  securing.
Place  the  LP  gas  tank  into  the  tank  tray  set.  Make  sure  the  tank  valve  facing  the  right  rear  corner  of
left  island.  Tighten  the  wing  bolt  to  secure  the  LP  gas  tank.  (

See Fig.3

)

Connect the LP regulator onto the LP gas tank.

CAUTION:

There shall be a minimum clearance of 2 inches (50.8 mm) between the floor of the LP-gas cylinder

enclosure and the ground.

Proper ventilation must be added to the island.

Manifold Extension Fitting

NG Regulator

Fig. 3

Island Bottom
Panel

Tank Tray Set

«
...
8
9
10
11
12
...
»

Содержание Grand Turbo B4019LP



































Отзывы:

Нет отзывов

Похожие инструкции для Grand Turbo B4019LP

Бренд: Naterial Страницы: 156

Бренд: Patton Страницы: 78

Tjome small FCC-PG-19500

Бренд: FCCBBQ Страницы: 12

Бренд: Napoleon Страницы: 60

Бренд: Ozito Страницы: 8

Бренд: Ice Страницы: 47

Бренд: Masterbuilt Страницы: 8

Бренд: Star Страницы: 8

120QP-21500 Series

Бренд: Quackenbush Страницы: 20

Бренд: Makita Страницы: 32

Бренд: Makita Страницы: 56

Бренд: Makita Страницы: 60

Бренд: Makita Страницы: 96

Бренд: Far Tools Страницы: 32

Бренд: BTI Страницы: 44

Бренд: GE Страницы: 4

Бренд: GE Страницы: 2

Бренд: GE Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды