Barbeques Galore Grand Turbo B4019LP Скачать руководство пользователя | Manualshive

Страница: 11 / 34

background image

11

5

Install Partition Panel

Ignitor Cap

Ignitor Slot

AA Battery

Spring

Install Ignitor Battery

Remove  Ignitor  Cap  from  Control  Panel.
Place  supplied  AA  battery  into  the  Ignitor  Slot  with  positive  pole  facing  you.
Position  the  Cap  and  Spring  over  the  AA  battery  and  tighten  onto  Control  Panel.

6

Partition Panel
(above the Gas Tank)

Fig. 4

Tank Tray Set

5"

22-24"

21"

1"

17-19"

5"

Vent Openings
must be at least
1/8" wide

Install  the  Partition  Panel  (not  included  in  this  unit)  onto  the  left  island.
Make  sure  there  is  22-24"  of  clearance  between  the  partition  panel  and  the  Tank
Holder  Assembly.
CAUTION:  Build  your  grill  island  before  installing  the  LP  Gas  Tank  and  Partition  Panel  (Not  included
in  this  unit).  Refer  to  the  heights  listed  in  Fig.  4  for  constructing  your  grill  island.  An  island  unit  is
not  included  with  the  purchase  of  your  Grill  Head.

«
...
9
10
11
12
13
...
»

Содержание Grand Turbo B4019LP



































Отзывы:

Нет отзывов

Похожие инструкции для Grand Turbo B4019LP

Бренд: Saber Compact Страницы: 84

Бренд: Saber Compact Страницы: 2

VPrestige PF600

Бренд: Napoleon Страницы: 40

Бренд: Zipper Mowers Страницы: 83

Бренд: Cembre Страницы: 56

Бренд: Char-Broil Страницы: 28

Бренд: Magma Страницы: 10

Бренд: Perfect Flame Страницы: 31

Бренд: Smeg Страницы: 4

Бренд: Napoleon Страницы: 28

Бренд: Hamrforge Страницы: 8

Asia Lounge ABP603BB

Бренд: Bestron Страницы: 40

Бренд: Weber Страницы: 29

Бренд: Klarstein Страницы: 124

Бренд: Summerset Страницы: 25

Бренд: Klarstein Страницы: 36

Бренд: DS Страницы: 36

Бренд: Hitachi Koki Страницы: 13

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды