background image

USE  AND  CARE  INSTRUCTIONS

16

Secure  a  20lb  LP  Gas  Tank  to  Gas  Grill

Note: 

You  can  only  use  a  20lb  LP  Gas  Tank  in  this

Gas  Grill.

NOTE:

  When  using  Propane,  EXTREME  CAUTION

should  be  used  to  provide  ample  ventilation  of  vapor
from  the  enclosure.  LP  Gas  vapor  is  heavier  than  air
and SERIOUS INJURY from a DANGEROUS  EXPLO-
SION  could occur  if LP  Gas is  allowed to  accumulate
in  an  enclosure  and  then  ignited.  Both  the  Barbecue
enclosure  and  LP  cylinder  enclosure  require  venting
that  must  be  provided  at  the  floor  level  of  the  enclo-
sure  to  allow  any  leaking  LP  Gas  vapor  to  escape
(see  Fig.  1).

NOTE: 

When installing a barbecue equipped for liquid

propane  in  an  island,  the  propane  tank  must  be  in
a  separate enclosure that is  completely  isolated from
the  barbecue.  It  must  be  cross-ventilated  in  accor-
dance  with  the  current  standards.  The  propane  tank
MUST  NEVER  be  installed  directly  under  the  barbe-
cue.
NOTE:  The  total  of  the  upper  ventilation  openings
must  be  a  minimum  of  20  sq.  inches.  The  total  of
the  lower  ventilation  openings  must  be  a  minimum
of  10  sq.  inches.  Upper  and  lower  ventilation  open-
ings  MUST  BE  PROVIDED  on  both  sides  of  built-in
construction.  The  top  of  the  upper  ventilations  open-
ings  must  be  located  within  5"  from  the  top  of  the
island.  The  bottom  of  the  lower  ventilation  openings
must be at least 1" or less from the floor of the island.
The  top  of  the  lower  ventilation  openings  cannot  be
more  than  5"  from  the  floor  of  the  island.  Every
ventilation opening must have a minimum of 1/8" (See
Fig.  4  on  page  22).  Contact  a 

Barbeques  Galore

s

associate  for  more  details.

Fig. 1

Stainless Steel Tube (Refer
to the Note below).

5/8" UNF
Thread

The built-in appliance for use with a remote self-contained LP
Gas supply system must use rigid pipe, semi-rigid tubing or a
connector complying with the Standard for Connections for
Gas Appliances, ANSI Z21.24/CSA6.10, or the standard for
Connectors  Outdoor  Gas Appliance  and  Manufactured
Homes, ANSI21.75/CSA 6.27 and suitable for outside installa-
tion. The maximum length of the connection shall be 6 ft(1.
82m).
The  connector  should  be  installed  at  the  location  visible
when  opening  the  door.
The connector must be away from any sharp points or sharp
edges.
When using semi-rigid tubing, do not use materials made of
aluminium or aluminium alloy.

Note:

Air Vents

Partition Panel

Non-Combustible
Construction, such as
stone, marble, cement

Содержание Grand Turbo B4019LP



































Отзывы: