Banner DF-G3 Long Range Expert Скачать руководство пользователя

Страница: 17 / 36

Method

Action

Result

SET

Button

Set the Mode switch to ADJ.

Display: Red - Signal Level; Green -

Threshold

Remote Input 6

action

is required; sensor is ready for

the Two-Point TEACH method

2. Teach the

first

condition.

Method

Action

Result

SET

Button

a. Present the

first

condition.

b. Click the SET rocker

button.

Display: Flashes "2Pt tch" then holds on

"1234 2nd"

Remote Input

a. Present the

first

condition.

b. Single-pulse the remote input.

3. Teach the second

condition.

Method

Action

Result

SET

Button

a. Present the second

condition.

b. Click the SET rocker

button.

TEACH Accepted
Displays alternate "PASS" and % Minimum

Difference

7; Sensor returns to Adjust

mode

TEACH Not Accepted
Displays alternate "FAIL" and % Minimum

Difference

7; Sensor returns to Adjust

mode

Remote Input

a. Present the second

condition.

b. Single-pulse the remote input.

4. Return to Run mode.

Method

Action

Result

SET

Button

Move the Mode switch to RUN

Display: Red - Signal Level; Green -

Threshold

Remote Input

action

is required; sensor returns to

RUN mode

automatically

3.5.2 Dynamic TEACH

• Teaches

on-the-fly

• Establishes a single switching threshold
• Threshold can be adjusted using "+" and "-" rocker

button

(Manual Adjust)

Dynamic TEACH is best used when a machine or process may not be stopped for teaching. The sensor learns during actual sensing

conditions,

taking

multiple

samples of the light and dark

conditions

and

automatically

setting

the threshold at the

optimum

level.

5 SET

Button:

0.04 seconds

≤

"Click"

≤

0.8 seconds

6 Remote Input: 0.04 seconds

≤

0.8 seconds

7 See

Troubleshooting

on page 25 for more

explanation

of the % Minimum

Difference

displayed

after

the Two-Point TEACH method.

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Содержание DF-G3 Long Range Expert




































Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации

Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды