manualshive.com logo in svg

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации, Страница: 16 / 36

Поделиться
Скачать
Banner DF-G3 Long Range Expert Скачать руководство пользователя страница 16

1.

Configure

 the 

first

 sensor as the Master (inPt SEL = MAST).

2. In the Master sensor set-up, enter the total number of Slave sensors you will be using (tOtL SLAV = 1 - 6).

3. For each Slave sensor used, 

configure

 the input as a Slave (inPt SEL = SLVE).

4. Give each Slave its own 

identifying

 address (SLAV Addr = 1 - 6).

5. Connect the Input wires of the Master and all of the Slaves together.

Note: Note: Giving two Slave sensors the same address will cause them to 

fire

 their 

emitters

 at the same 

time

 in the 

firing

sequence.

3.5 Adjust Mode 

Sliding the RUN/PRG/ADJ mode switch to the ADJ 

position

 allows the user to perform Expert TEACH/SET methods and Manual

Adjustment of the threshold(s).

Note: For the Dual Output models, when teaching CH2, the gain 

setting

 will be the same as the gain 

setting

 made during the CH1

teach. Reteaching CH1 may invalidate the previous CH2 teach.

3.5.1 Two-Point TEACH

• Establishes a single switching threshold

• Threshold can be adjusted by using the "+" and "-" rocker 

button

 (Manual Adjust)

Two-Point TEACH is used when two 

conditions

 can be presented 

statically

 to the sensor. The sensor locates a single sensing threshold

(the switch point) midway between the two taught 

conditions,

 with the Output ON 

condition

 on one side, and the Output OFF 

condition

on the other.

Sensor positions 

threshold midway 

between taught conditions

Darkest

(no signal)

Most Light

(saturated

signal)

Output OFF

Output ON

Darkest Taught

Condition

Lightest Taught

Condition

Position

adjusted by

Manual Adjust

Figure 6. Two-Point TEACH (Light Operate shown)

The Output ON and OFF 

conditions

 can be reversed by using the LO/DO (Light Operate/ Dark Operate) switch or through the program

interface for the dual output model.

Two-Point TEACH and Manual Adjust

Moves switching threshold value up or down to make adjustments

• Slide Mode switch to ADJ to enter Adjust mode

• Press "+" to increase; press "-" to decrease

◦

GREEN display shows the switching threshold value

◦

2 seconds 

after

 adjustment, the GREEN display will 

flash

 3 

times

 to 

confirm

• Slide Mode switch to RUN to complete 

operation

Remember: Manual adjustments are disabled when Auto Thresholds are ON

Follow these steps to perform a Two-Point TEACH:

Note: TEACH 

Selection

 must be programmed to 2Pt tcH.

1. Enter Adjust mode.

DF-G3 Long Range Expert

™

 Dual Display Fiber 

Amplifier

 

 

16

www.bannerengineering.com - Tel: 763.544.3164

 

Содержание DF-G3 Long Range Expert





































Отзывы:

Нет отзывов