Banner DF-G3 Long Range Expert Скачать руководство пользователя

Страница: 14 / 36

3.2.10 Gain

Selection

The DF-G3 can operate in Auto Gain mode or the Gain can be

fixed

to be in Gain 1...7. In Auto Gain, the DF-G3

optimizes

the gain during

a TEACH/SET method for the presented

condition(s).

While viewing the

fixed

gains in the Gain

Selection

choice list, the DF-G3 will

automatically

switch to the selected gain and display the measured signal on the Red display. This allows for easy and quick

evaluation

of the

fixed

gain mode.

3.2.11 Factory Defaults

The Factory Defaults menu allows the DF-G3 to be easily restored back to original factory default

settings

(see Factory Default

Settings

Specifications

3.3 Remote Input

Use the input wire to program the sensor remotely. To program the sensor using the input wire, remote input must be enabled (inPt SEL

= SEt, see

Input Wire

Function

on page 13). The remote input provides limited programming

options

(see the

figure

below). Pulse the

remote input according to the

figures

and the

instructions

provided in this manual.

Note: For NPN models, the remote input pulses are

active

low as shown in the following

figures.

For PNP models, the remote

input pulses are

active

high and are inverted from the following

figures.

Button Unlock (uloc)
Button Lock (loc)

Remote

Input

One-Point Window

One-Point Light Set

CAL Set

One-Point Dark Set

Two-Point
Dynamic

Remote Setup

REMOTE TEACH

REMOTE SETUP

Teach Selection

Completes Teach

Starts Selected Teach

0.04 seconds < T < 0.8 seconds
Timing between Pulse groups > 1 second

Pulse Timing (T)

NOTE: Follow procedure for the selected TEACH/SET method
(highlighted in black box) chosen in the TEACH Selection menu

Button Lock (loc) or Unlock (uloc)

Factory Default Settings

Figure 4. Single Output—Remote Input Flowchart

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Содержание DF-G3 Long Range Expert




































Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации

Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды