manualshive.com logo in svg

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации, Страница: 21 / 36

Поделиться
Скачать
Banner DF-G3 Long Range Expert Скачать руководство пользователя страница 21

3.5.4 Light SET

• Sets a threshold a programmable % 

offset

 below the presented 

condition

• Changes output state on any 

condition

 darker than the threshold 

condition

• Threshold can be adjusted using "+" and "-" rocker 

button

 (Manual Adjust)

• Recommended for 

applications

 where only one 

condition

 is known, for example a stable light background with varying darker

targets

• See Program Mode for programming the 

Offset

 Percent 

setting

A single sensing 

condition

 is presented, and the sensor 

positions

 a threshold a programmable % 

offset

 below the presented 

condition.

When a 

condition

 darker than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO 

setting.

Threshold position 

adjusted by 

Manual Adjust

Sensor positions
threshold a programmable
 % offset below the 
presented condition

Darkest

(no signal)

Most Light

(saturated

signal)

Output OFF

Output ON

Condition 
Presented

Figure 10. Light SET (Light Operate shown)

Light SET and Manual Adjust

Moves switching threshold value up or down to make adjustments

• Slide Mode switch to ADJ to enter Adjust mode

• Press "+" to increase; press "-" to decrease

◦

GREEN display shows the switching threshold value

◦

2 seconds 

after

 adjustment, the GREEN display will 

flash

 3 

times

 to 

confirm

• Slide Mode switch to RUN to complete 

operation

Remember: Manual adjustments are disabled when Auto Thresholds are ON

Follow these steps to perform a Light SET:

Note: TEACH 

Selection

 must be programmed to Lt SEt.

1. Enter Adjust Mode

Method

Action

Result

SET 

Button

 14

Set Mode switch to ADJ

Display: Red - Signal Level; Green -

Threshold

Remote Input 15

No 

action

 is required; sensor is ready for

Light SET method

2. SET Sensing 

Condition

14 SET 

Button:

 0.04 seconds 

≤

 "Click" 

≤

 0.8 seconds

15 Remote Input: 0.04 seconds 

≤

 T 

≤

 0.8 seconds

 

 

DF-G3 Long Range Expert

™

 Dual Display Fiber 

Amplifier

 

www.bannerengineering.com - Tel: 763.544.3164

21

Содержание DF-G3 Long Range Expert





































Отзывы:

Нет отзывов