Banner DF-G3 Long Range Expert Скачать руководство пользователя

Страница: 11 / 36

Channel 2 Menu
Program (PRG) mode allows the following

settings

to be programmed in the DF-G3.

The LO/DO switch is replaced with the CH1/CH2

selection

switch. LO/DO is selected via the

Program Mode menu.

Setting

the switch to CH1

allows the

settings

in the Program Mode chart to

be programmed globally for CH1 and CH2.
When CH2 is selected in Program mode, the

settings

below can be

configured

for CH2 and are

independent from CH1

settings.

CH2 Factory Default

Settings:

Out SEL2

tch SEL2

2-pt tch

OFSt Pct2

10 pct

Auto Thr2

oFF

dLY SEL2

oFF

SenS CH2

std

The factory default

settings

for CH2 and CH1 are

the same.

(+)

(-)

to set value

(+)

(-)

to set value

To scroll through menu lists: Press “+” or “-” To enter a choice list or to select and save: Click SET To exit a choice list without saving: Press and hold SET for 2 seconds

Click SET

to enter choice list

Press and hold SET to exit

choice list without saving

DISPLA

LOOP

Return to Menu List

PROGRAM MODE

Switch Mode

to “PRG”

Click SET

to enter choice list

Click SET

to enter choice list

DISPLA

LOOP

Click SET

to enter choice list

Click SET

rocker button

Click SET to select and save a choice in any list

Menu List

on display represents a “w”

on display represents a “m”

Click SET

to enter choice list

default setting

other menus hidden

setting-specific

Click SET

to enter choice list

ISPLA

LOOP

(+)

(-)

to set value

Click SET

(+)

(-)

to set value

Click SET

(+)

(-)

to set value

Click SET

(+)

(-)

to set value

Click SET

(+)

(-)

to set value

Click SET

DISPLA

LOOP

DISPLA

LOOP

DISPLA

LOOP

Available in Lt, dr or wind set only

Not available in CAL Set

3.2.1 Output

Selection

Both CH1 and CH2 can be programmed for either light operate (LO) or dark operate (DO). The Channel 2 menu includes two

additional

menus: Health (Health Mode Alarm) and Comp (Complementary Programming).

Health Mode Alarm

The Health Mode Alarm alerts you when

preventative

maintenance becomes necessary to ensure reliable sensing. The Health Mode

output 2 is

Active

when the system is OK and

operating

normally. Health Mode output 2 becomes

Inactive

when the system is in a

marginal state because of

contamination.

The system

still

operates normally and can detect small objects, but is nearing the alarm

state. When the system is completely contaminated and unable to ensure reliable sensing, the system goes into the alarm state. In the

alarm state, the discrete output 1 is forced to the blocked state and can no longer be used to detect small objects.

• Threshold Alert

displays when Health Mode output 2 is

inactive

because of

contamination.

The system operates

normally but is nearing the alarm state.

• Threshold Error

displays when discrete output 1 is forced to the blocked state and can no longer be used to

detect small objects.

The sensor may enter Health Mode Alarm for any of these reasons:

1. When

first

powered up; the

fiber

optic

array may already be contaminated

2. If the Window SET procedure fails,

indicating

the

fiber

optic

array is contaminated and the sensor could not set a valid clear-

state light level for reliable

detection

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Содержание DF-G3 Long Range Expert




































Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации

Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды