Banner DF-G3 Long Range Expert Скачать руководство пользователя

Страница: 23 / 36

Remember: Manual adjustments are disabled when Auto Thresholds are ON

Follow these steps to perform a Dark SET:

Note: TEACH

Selection

must be programmed to dr SEt.

1. Enter Adjust Mode.

Method

Action

Result

SET

Button

Set Mode switch to ADJ

Display: Red - Signal Level; Green -

Threshold

Remote Input 18

action

required; sensor is ready for Dark

SET method

2. SET Sensing

Condition.

Method

Action

Result

SET

Button

•

Present sensing

condition

•

Click the SET rocker

button

Threshold

Condition

Accepted Displays

read "dr SEt" then alternate "PASS" with %

Offset

19; Sensor returns to Adjust mode

Threshold

Condition

Not Accepted

Displays read "dr SEt" then alternate

"FAIL" with minimum %

Offset

19 for

sensing

condition;

Sensor returns to Adjust

mode

Remote Input

•

Present sensing

condition

•

Single-pulse the remote input

3. Return to RUN Mode.

Method

Action

Result

SET

Button

Move Mode switch to RUN

Display: Red - Signal Level; Green -

Threshold

Remote Input

action

required; sensor returns to RUN

mode

automatically

3.5.6

Calibration

SET

• Sets a threshold exactly at the presented

condition

• Threshold can be adjusted using "+" and "-" rocker

button

(Manual Adjust)

A single sensing

condition

is presented, and the sensor

positions

a threshold exactly at the presented

condition.

When a

condition

lighter than the threshold is sensed, the output either turns ON or OFF, depending on the LO/DO

setting.

17 SET

Button:

0.04 seconds

≤

"Click"

≤

0.8 seconds

18 Remote Input: 0.04 seconds

≤

0.8 seconds

19 See

Troubleshooting

on page 25 for more

explanation

of the %

Offset

displayed

after

the Dark SET method

DF-G3 Long Range Expert

™

Dual Display Fiber

Amplifier

www.bannerengineering.com - Tel: 763.544.3164

Содержание DF-G3 Long Range Expert




































Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации

Результаты поиска

Содержание DF-G3 Long Range Expert

Отзывы:

Похожие инструкции для DF-G3 Long Range Expert

Бренды по названию

Популярные бренды