manualshive.com logo in svg

Banner DF-G3 Long Range Expert, Инструкция по эксплуатации, Страница: 25 / 36

Поделиться
Скачать
Banner DF-G3 Long Range Expert Скачать руководство пользователя страница 25

Method

Action

Result

SET 

Button

Move Mode switch to RUN

Display: Red - Signal Level; Green -

Threshold

Remote Input

No 

action

 required; sensor returns to RUN

mode 

automatically

3.6 

Troubleshooting

3.6.1 Manual Adjustments Disabled

Manual adjustments are disabled when Auto Thresholds are ON. If a manual adjustment is 

attempted

 while Auto Thresholds are ON,

the Green display will 

flash

 

.

3.6.2 Percent Minimum 

Difference

 

after

 TEACH

The Two-Point and Dynamic TEACH methods will 

flash

 a % minimum 

difference

 on the displays 

after

 a PASS or FAIL.

Value

PASS/FAIL

Description

0 to 99%

FAIL

The 

difference

 of the taught 

conditions

 does not meet the required minimum

100 to 300%

PASS

The 

difference

 of the taught 

conditions

 just meets/exceeds the required minimum, minor

sensing variables may 

affect

 sensing reliability

300 to 600%

PASS

The 

difference

 of the taught 

conditions

 

sufficiently

 exceeds the required minimum, minor

sensing variables will not 

affect

 sensing reliability

600% +

PASS

The 

difference

 of the taught 

conditions

 greatly exceeds the required minimum, very stable

operation

3.6.3 Percent 

Offset

 

after

 SET

The Window, Dark, and Light SET methods will 

flash

 a % 

offset

 on the displays 

after

 a PASS or FAIL.

SET Result

% 

Offset

 Meaning

PASS (with % 

Offset)

Displays the % 

offset

 used for the SET method

FAIL (with % 

Offset)

Displays the minimum required % 

offset

 necessary to PASS the SET method

FAIL (without % 

Offset)

Presented 

condition

 cannot be used for the SET method

3.6.4 Threshold Alert or Threshold Error

Severe 

contamination/changes

 in the taught 

condition

 can prevent the Auto Thresholds algorithm from 

optimizing

 the threshold(s).

State

Display

Description

Corrective

 

Action

Threshold Alert

Alternates

 and

The threshold(s) cannot be 

optimized,

but the sensor's output will 

still

continue

 to 

function

Cleaning/correcting

 the sensing

environment and/or a re-teach of the sensor

is highly recommended

Threshold Error

The threshold(s) cannot be 

optimized,

and the sensor's output will stop

functioning

Cleaning/correcting

 the sensing

environment and/or a re-teach of the sensor

is required

 

 

DF-G3 Long Range Expert

™

 Dual Display Fiber 

Amplifier

 

www.bannerengineering.com - Tel: 763.544.3164

25

Содержание DF-G3 Long Range Expert





































Отзывы:

Нет отзывов