Bandit BTC-150 Скачать руководство пользователя страница 82

Страница: 82 / 113

Bandit

MODEL BTC-150

245811760545 29Dec2017

Page 1

Main1 (Grinder)

(The Display automatically returns to this Main Engine page 60sec after last button press).

1. Cutter Head is turned On/Off at Keypad, Speed adjusted Up/Dn at Keypad as well.

2. Swing Speed Limit is adjusted by finger wheel on Right Joystick. When Load Control (16) is

turned ON at Keypad, the small number behind the Swing Speed % is an automatic limit that

slows the Swing Speed when engine is lugging down in a hard cut.

3. Shows which machine mode is selected, Stump Grinder or Mower as selected in Setup2.

4. Indicates status of Seat Switch. If the operator leaves the seat for 3sec or more, the engine

will idle down and hydraulic functions will be disabled.

5. Indicates status of E-Stop Switch.

6. and 7. Navigate to Setup Options and Maintenance information.

8. Momentary button to force a fan purge on the reversing fan systems; will reverse for 20secs.

10. and 11. Increase / Decrease Eng RPM. Throttle Command (shown below Eng RPM gauge).

Can also Inc/Dec Eng RPM on LH Joystick.

14. Warning icon indicates a Pop-up diagnostic message is hidden, press this button to recall.

15. Blinking alert that shows Hydraulics Disabled is pressed on the Keypad. When Hydraulics

Disabled is pressed, the engine will idle down and all machine functions will be disabled EXCEPT

for the hydraulic cooler motors.

16. “Load Control” will appear to indicate that Load Control is turned ON at the Keypad.

18. Tier 4 emissions icons and indicators.

19. Blinking

indicates that the system has been E-Stopped.

20. Track Motor Displacement indicator, select Slow or Fast on LH Joystick.

21. Diesel Exhaust Fluid (DEF) Tank Level. If less than 12% the DEF level icon will blink red.

22. Track Speed Limit is adjusted 1-100% on the LH Joystick finger wheel. If the tracks are

limited to anything less than full speed 100% (i.e. 70% in the example screen shot), pushing the

LH Joystick all the way fwd/rev will only allow 70% speed output to the tracks.

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды