Bandit BTC-150 Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 113

background image

Bandit

42

Copyright 3/19

MODEL BTC-150

MAINTENANCE

CUTTER WHEEL - GREEN TEETH

There are thirty-two (32) teeth and pockets, and

thirty-two (32) tooth nuts to a complete set on a

Model BTC-150 Green Tooth Wheel. Thirty-two

(32) pockets: twelve (12) threaded right pockets,

twelve (12) counter-bored left pockets, two (2)

threaded straight pockets, two (2) counter-bored

straight pockets, two (2) threaded left pockets, two

(2) counter-bored right pockets, and thirty-two (32)

hex bolts.

DO NOT OPERATE MACHINE WITHOUT A FULL SET OF TEETH. OPERATING MACHINE WITHOUT A

FULL SET OF TEETH CAN CAUSE EXCESSIVE VIBRATION AND PREMATURE BEARING FAILURE.

Inspect pockets, teeth and bolts for damage and

replace as required.
When replacing pockets, always replace new

pockets across from each other (180°) in order to

prevent vibration.
Replacement teeth must be carbide tipped and of

like design as provided with the machine.
Use anti-seize on threads to help prevent bolts from

“freezing up” in cutter wheel pockets.

When replacing complete set of teeth, be sure to

duplicate original factory tooth arrangement. Torque

pocket bolts to 240 ft. lbs. (325 Nm). Torque tooth

nuts to 50 ft.-lbs. (67 Nm).

Do Not operate machine with extremely worn or

broken teeth.

DANGER

!

DANGER

!

DANGER

!

Before attempting any type of maintenance,

disengage clutch or cutter head engagement, wait for

the cutter head to come to a complete stop, place the

cutter head on the ground, turn off engine, remove

the ignition key, make sure the ignition key is in your

possession, and wait 2 minutes then disconnect the

battery. Make sure the cutter head is set on the ground

or securely blocked up and also chained before doing

any work around or under it.

DO NOT go near the rotating cutter head for any

reason. DO NOT go near the cutter head while the

engine is running or the cutter head is coasting to a

stop. Contact with a rotating cutter head will result

in serious bodily injury or death.

DANGER

!

NEVER USE HAND ON CUTTER WHEEL TO

HOLD IN PLACE WHILE CHANGING TEETH.

BE SURE TO REMOVE LOCKING PIN BEFORE

OPERATING THE MACHINE.

A locking pin is provided to hold the cutter wheel

in position during tooth removal and reinstallation.

Locking pin will only lock on outer teeth.

Use only original equipment manufacturer’s teeth.

The use of any other aftermarket teeth may cause

damage or premature failure to the drive train.

TOOTH ARRANGEMENT

WearSharp Tooth ........................900-9918-24
WearSharp Tooth Nut .................900-9918-50
Threaded Right Angled Pocket .....900-9907-10
C'bored Left Angled Pocket ........900-9907-09
Threaded Straight Pocket ........... 900-9907-11
C'bored Straight Pocket ..............900-9907-47
Threaded Left Angled Pocket .....900-9907-49
C'Bored Right Angled Pocket .....900-9907-48
Pocket Bolt .................................900-9907-13

«
...
42
43
44
45
46
...
»

Содержание BTC-150


















































































































Отзывы:

Нет отзывов

Похожие инструкции для BTC-150

Бренд: Camozzi Страницы: 2

Бренд: Oktober Страницы: 22

Бренд: 1010music Страницы: 2

Бренд: 1010music Страницы: 4

Бренд: Bard Страницы: 144

Бренд: Vahva Jussi Страницы: 9

Бренд: h/p/cosmos Страницы: 81

Бренд: Maeda Страницы: 276

Бренд: Salter Страницы: 18

Бренд: Salter Страницы: 42

Бренд: Salter Страницы: 47

Бренд: Salter Страницы: 35

Бренд: Salter Страницы: 40

M-041 INDOOR CROSS

Бренд: Salter Страницы: 15

Бренд: zapco Страницы: 14

Бренд: Daavlin Страницы: 55

Бренд: Daavlin Страницы: 19

Бренд: Eleiko Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды