Bandit BTC-150 Скачать руководство пользователя страница 13

Страница: 13 / 113

Bandit

MODEL BTC-150

SAFETY PROCEDURES

Do not attempt to operate the machine on an ascending or descending slope of more than 25° or 46% or

a side slope of more than 17° or 30%, it is Dangerous and could be Fatal. This is the maximum slope grade

the machine can be operated on if the hydraulic system, self propelled undercarriage, and engine are running

at maximum performance and good traction is sustained.

The machine should never be parked on a slope at any time. The machine can coast or creep causing

equipment and/or personal injury.

Make sure everyone is clear of machine before moving the machine. Stay clear of undercarriage travel

system when the machine is moving.

DO NOT entangle feet or hands in undercarriage travel system.

NEVER sit, stand, lay, climb or ride anywhere on this machine while it is running, operating, or in transit.

You will be injured.

Use

EXTREME CAUTION

when traveling over non-level surface! This machine can tip over or tip backwards

on non-level surface. You will cause engine damage, machine damage and possible personal injury!

Any increase from the specified maximum operating angles may cause loss of lubrication function and

damage the engine.

IF MACHINE IS EQUIPPED WITH A SELF PROPELLED UNDERCARRIAGE

Machines equipped with undercarriage tracks are shipped with a manual from the track manufacturer.

Refer to it for service, operation, and safety information.

SAFETY PROCEDURES

DANGER

WARNING

25° MAX.

17° MAX.

Maximum Slope Grade

Diagram shows percentage to degree of slope.

Percentage is in vertical feet for every 100 horizontal feet.

Ascending or Descending Slope

Side Slope

100 FT. (30.5 m)

46 FT.

(14 m)

(46%)

30 FT.

(9.1 m)

(30%)

25° MAX.

17° MAX.

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды