Bandit BTC-150 Скачать руководство пользователя страница 11

Страница: 11 / 113

Bandit

MODEL BTC-150

SAFETY PROCEDURES

DO NOT start to grind/mow unless you are

completely sure there are not any utility lines in the

area above or below the ground level where you are

grinding/mowing. Always contact the utility locating

service in your area or local utility companies to mark

underground utility lines.

Before attempting any type of maintenance,

disengage clutch or cutter head engagement, wait for

the cutter head to come to a complete stop, place the

cutter head on the ground, turn off engine, remove

the ignition key, make sure the ignition key is in your

possession, and wait 2 minutes then disconnect the

battery. Make sure the cutter head is set on the ground

or securely blocked up and also chained before doing

any work around or under it.

DANGER

DO NOT go near the rotating cutter head for any

reason. DO NOT go near the cutter head while the

engine is running or the cutter head is coasting to a

stop. Contact with a rotating cutter head will result

in serious bodily injury or death.

Avoid moving parts. Keep hands, feet, and clothing

away from power driven parts. Keep all guards and

shields in place and properly secured.

DANGER

Never grind/mow materials that might contain

wires, stones, nails, or other metal objects which

may damage the teeth and become dangerous

projectiles. Remove all rocks and stones from work

area.

DO NOT go near or in-line with the debris

field of the machine while in operation. While

grinding/mowing, the chips and portions of the

material fly from the cutter head and can cause

severe injury.

DANGER

Before attempting any type of maintenance or

service work under the cab make sure the cylinder

lock is in place.

DANGER

Do not attempt to start the engine, engage

the cutter head or engage the engine PTO

(power-take-off) system on this machine if the cutter

head is jammed or frozen in place. If you do, you will

damage or ruin the drive belts, the hydraulic system,

and/or the PTO which will not be covered under

warranty and will cost you down time and money.

NOTICE

DANGER

Avoid power lines. Electrocution is possible if the

machine touches a power line. Take the following

precautions. Keep the machine at least 10 feet

(3 meters) from electric lines. If the machine contacts

an electric line stay away from the machine.

WARNING

Sparks can occur if cutter teeth strike rocks, metal,

or other hard objects.

DO NOT use in high or very high fire hazard

severity zones.

Operation of this equipment may create sparks

that can start fires around dry vegetation. A spark

arrester may be required. The operator should

contact local fire agencies for laws or regulations

relating to fire prevention requirements.

Do Not continue to operate the machine if the

cutter head stalls. Immediately lift cutter head out

of the stump, material, dirt, etc. and start again with

less bite. Prolonged cutter head stall will ruin the

hydraulic components, creating extreme heat and

possible fire hazard.

Do not operate the machine with the cab doors

opened. Leaving the cab doors open while the

machine is in operation can cause serious injury or

death.

WARNING

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды