Bandit BTC-150 Скачать руководство пользователя страница 87

Страница: 87 / 113

Bandit

MODEL BTC-150

245811760545 29Dec2017

Page 6

Setup

1. Navigate back.

2. Navigate to Setup3 page and more setup options.

5. and 8. Highlight Up or Down to the next value you would like to adjust.

6. and 7. Adjust the value that is currently highlighted.

Machine Mode can only be change with Key ON, Engine NOT running.

Select Drive Settings allows more than one operator to choose between two separate drive

setting groups on Setup7 and Setup8. Each drive group can be adjusted to how separate

operators prefer to drive the machine.

Fan Reverse Interval is optional on some machines. It is the time between fan reversing cycles

to purge debris from the fan shrouds. The reverse cycle typically lasts between 20-30 seconds.

Track speed settings allow the operator to trim the maximum track speed for straight travel if

they drift out of alignment with wear over time.

There are 3 different track drive Ramp Ranges that can be selected to adjust how quickly the

tracks stop and go. Range[3] is the most responsive, Range[1] is slower and soft. If the Ramp

Range is changed, the operator should test the Creep Fwd trigger again because the drive

ramps have an effect on Creep Time ; which may need to be readjusted along with Ramp

Range.

9. Shows total hours of operation for the selected attachment.

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды