Bandit BTC-150 Скачать руководство пользователя страница 110

Страница: 110 / 113

Bandit

108

MODEL BTC-150

245811760545 29Dec2017

Page 29

[ControlLights]

- If communication is lost with Keypad A3, lights will turn ON.

[ControlLockPins]

- HydDisable, EngRunOut, not SeatSwDelay, disables Lock Pins

[ControlMain]

- HydDisable, EngRunOut, not SeatSwDelay, disables Main

- Float Trigger has 200ms delay.

- Not Mower Mode, HydDisable, EngRunOut, not SeatSwDelay, disables Float

- Separate Float valve vs Main U/D valve w/ 4

-pos

[ControlPushBar]

- Not Mower Mode, HydDisable, EngRunOut, not SeatSwDelay, disables PushBar

[ControlStarter]

- Volvo start command sent via J1939 (FF46)

KeyStartIn

will sound start beeper

(StartHornOut)

for 50ms seconds and then fire starter

solenoid

(StartSolOut)

- If the Eng E-Stop has been triggered, dead-crank starting is permitted, but engine will not fire.

- If Eng Speed is above 450rpm for 300ms start cranking is prevented.

[ControlSwing]

- Not Grinder Mode, HydDisable, EngRunOut, not SeatSwDelay, disables Swing

- Mod10h34 is Gate in Mower, Swing in Grinder

[ControlTilt]

- HydDisable, EngRunOut, not SeatSwDelay, disables Tilt

[ControlTracks]

- HydDisable, EngRunOut, not SeatSwDelay, disables Tracks

- Track Reverse on either track will fire TrackBeeper

- RampRange1 Ascend 1000/1000 per sec, Descend 2500/1000 per sec

- RampRange2 Ascend 2500/1000 per sec, Descend 2500/1000 per sec

- RampRange3 Ascend 5000/1000 per sec, Descend 5000/1000 per sec

[ControlWinch]

- Head ON, HydDisable, EngRunOut, not SeatSwDelay, disables Winch

[Inputs]

- Seat Switch has 3sec OFF delay

- E-Stop has 100ms OFF delay

- Accum Sw forced true has 5sec OFF delay

[Outputs]

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды