Bandit BTC-150 Скачать руководство пользователя страница 10

Страница: 10 / 113

Bandit

MODEL BTC-150

SAFETY PROCEDURES

It is very important after you have operated a new

machine for approximately an hour to shut down the

machine and recheck all nuts and bolts. It is normal

for nuts and bolts to loosen once on a new piece of

machinery. If you tighten them now, there is a good

possibility they won’t loosen again. Certain nuts and

bolts should be checked periodically such as cutter

teeth bolts for torque and fit.

Most of the nuts used on the Bandit Track Carrier

are self locking. After a nut or bolt has been removed

five times, it should be replaced to ensure proper

tightness. This is especially critical on the cutter tooth

bolts!

After the engine is started, let the grinder wheel

turn at the lowest RPM’s possible. Listen for any type

of noise that is foreign. Any steel on steel noise is

foreign. If you hear a noise, stop the engine, find the

problem and fix it.

It is very important after you have operated a new

machine for approximately an hour to shut down the

machine and recheck all hydraulic fittings. Relieve

all pressures and retighten as needed.

DO NOT GO NEAR HYDRAULIC LEAKS! High

pressure oil easily punctures skin causing serious

injury, gangrene, or death. Avoid burns from fluid.

Hot fluid under pressure can cause severe burns.

DO NOT use fingers or skin to check for leaks. Lower

load or relieve hydraulic pressure before loosening

fittings. Relieve all pressure in the system before

disconnecting the lines, hoses, or performing other

work. Use a piece of cardboard to find leaks. Never

use your bare hands. Allow system to cool down to

ambient temperature before opening any coolant or

hydraulic oil system.

In cold weather situations let your hydraulic

system idle for approximately 15 minutes to allow

the system to warm up to operating temperature.

WARNING

Never use jumper cables during freezing

temperatures. Tow the machine inside and allow

the battery time to warm up. If the machine must

be started outside, inspect the battery acid for ice

formation. Explosion will occur with a frozen battery.

If the machine is going to be operated in excessively

cold conditions, a larger cold cranking amp battery

may be needed to ensure proper and prompt

starting. Never use jumper cables in a confined or

unventilated area. Battery acid fumes are explosive.

Battery acid can cause severe burns. Never expose

an open flame or spark near the battery. Keep all

burning materials away from the battery. When

servicing the battery, shield eyes and face, and do

not smoke. Service in a well ventilated area.

DANGER

WARNING

Expensive damage to the Bandit will occur if

proper preparation is not taken before welding on

the machine. Be sure to disconnect both battery

cables and the engine ECM (engine control module)

before welding. Follow the specific Engine MFG.

instructions for proper welding and grounding

procedures, before attempting to weld on the

machine. If welding on the machine, do not ground

the welder through the machine bearings, ground

near work to be performed.

NOTICE

Keep the machine in good condition. Be sure the

machine is in good operating condition and that all

safety devices, including guards and shields are

installed and functioning properly. Visually inspect

the machine daily before starting the machine. Refer

to the “Daily Start Up & Maintenance”. Make no

modifications to your equipment unless specifically

recommended or requested by Bandit Industries Inc.

DANGER

DO NOT operate this machine unless all hydraulic

control devices operate properly. They must function,

shift and position smoothly and accurately at all

times. Faulty controls can cause personal injury!

WARNING

DO NOT operate this machine indoors! Exhaust

fumes can be fatal. Never refuel while the machine is

running. Never refuel in the shop or building. Always

refuel in a well ventilated area, away from sparks

or open flames, DO NOT SMOKE. Extinguish all

smoking materials. Wipe up all spilled fuel before

restarting the engine. Do not fill above 1/2” (12.7mm)

from top of tank for diesel engines and 2” (50mm)

from the top of the tank for gasoline engines.

To obtain the most from your machine, for the least

amount of cost, it is a good practice to set up and follow

a scheduled preventative maintenance program. It will

eliminate many possible problems and down time.

Engage and disengage cutter head at low rpm.

NOTICE

DO NOT operate machine with extremely worn or

broken teeth.

DANGER

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды