Bandit BTC-150 Скачать руководство пользователя страница 56

Страница: 56 / 113

Bandit

MODEL BTC-150

HYDRAULICS

DO NOT UNDER ANY CIRCUMSTANCES OVER-SET THESE RELIEF PRESSURES, BECAUSE IT WILL

CAUSE DAMAGE TO COMPONENT PARTS AS WELL AS HYDRAULIC PARTS.

These typical hydraulic fl ows and relief pressure settings are with the engine at full RPM. All settings are

subject to change!

When returning hydraulic components for warranty make sure to box up all warranted parts to avoid additional

damage while shipping.

Do not disassemble any hydraulic components which are to be warranted.

Anything which has been disassembled or tampered with will not be warranted. Items being returned must

be clean. All hydraulic components must have all hosing ports plugged. Failure to plug ports will allow debris

to enter components which will void warranty.

NOTICE

In cold weather situations, let the hydraulic system idle for approximately 15 minutes to allow the system

to warm up to operating temperature. Running cold oil through the hydrostatic motor can raise the case drain

pressures and damage the shaft seals.

NOTICE

HYDRAULICS

Some equipment and components such as a fl uid engagement clutch (PTO) have their own lubrication

requirements. Consult their manufactures manual for that information.

NOTICE

Before attempting any type of maintenance or service work under the cab make sure the cylinder lock is in place.

DANGER

Before attempting any type of maintenance, disengage clutch or cutter head engagement, wait for the cutter

head to come to a complete stop, place the cutter head on the ground, turn off engine, remove the ignition

key, make sure the ignition key is in your possession, and wait 2 minutes then disconnect the battery. Make

sure the cutter head is set on the ground or securely blocked up and also chained before doing any work around

or under it.

After the initial start-up of the machine and after any replacement of hydraulic components, fi ttings and

hoses must be re-checked for leaks and clearances.

CAUTION

Cylinder Lock in place on the Cab Tilt

Cylinder

Содержание BTC-150


















































































































Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды

Bandit BTC-150, Руководство по эксплуатации

Результаты поиска

Содержание BTC-150

Отзывы:

Похожие инструкции для BTC-150

Бренды по названию

Популярные бренды