manualshive.com logo in svg

Bailey infi 90 40 Series, Руководство по оборудованию

На нашем сайте вы можете бесплатно скачать руководство по оборудованию Bailey infi 90 40 Series. Этот Hardware Manual поможет вам разобраться с функционалом продукта и настроить его по вашим требованиям. Скачайте его с manualshive.com и получите полезные инструкции для использования продукта.

Поделиться
Скачать
background image

Table of Contents

Page

WBPEEUI220754A0   

iii

SECTION 1 - INTRODUCTION ....................................................................................................1-1

OVERVIEW ..................................................................................................................1-1
INTENDED USER .........................................................................................................1-1
OIS DESCRIPTION .......................................................................................................1-1

Console Hardware..................................................................................................1-2
Driver Cabinet Hardware .......................................................................................1-3

INSTRUCTION CONTENT .............................................................................................1-4
HOW TO USE THIS INSTRUCTION ...............................................................................1-4
DOCUMENT CONVENTIONS ........................................................................................1-5
GLOSSARY OF TERMS AND ABBREVIATIONS .............................................................1-5
REFERENCE DOCUMENTS..........................................................................................1-5
NOMENCLATURE ........................................................................................................1-5
OIS CONSOLE SPECIFICATIONS .................................................................................1-6

SECTION 2 - DESCRIPTION AND OPERATION........................................................................2-1

INTRODUCTION ...........................................................................................................2-1
CONSOLE FUNCTIONAL OPERATION ..........................................................................2-2

SECTION 3 - INSTALLATION .....................................................................................................3-1

INTRODUCTION ...........................................................................................................3-1
SPECIAL HANDLING ....................................................................................................3-1
UNPACKING AND INSPECTION ....................................................................................3-2
GENERAL INSTALLATION PROCEDURES ....................................................................3-3
CONSOLE CABINET INSTALLATION.............................................................................3-4
OIS DRIVER CABINET INSTALLATION .........................................................................3-7
AC POWER WIRING GUIDELINES ................................................................................3-8
AC OUTLETS ...............................................................................................................3-9
WIRING CONNECTIONS AND CABLING .....................................................................3-10
OPERATOR INTERFACE DEVICES .............................................................................3-15

Operator Keyboard...............................................................................................3-15
IIAKB04 Engineering Keyboard ............................................................................3-16
IIATB02 Trackball and IIAMS03 Mouse ................................................................3-17
IIADP01 Annunciator Display Panel .....................................................................3-17
IIADP02 Annunciator Display Panel .....................................................................3-17
Touch Screen .......................................................................................................3-19

Controller Card Installation ...........................................................................3-19
Touch Screen Installation ..............................................................................3-20
Calibrating the Touch Screen .........................................................................3-20
Touch Screen Jumper Settings ......................................................................3-21

PERIPHERALS ...........................................................................................................3-21

SCSI Bus Hardware .............................................................................................3-22
Printers................................................................................................................3-23

IIPRT02, IIPRT03, IIPRT05 and IIPRT09_ Printers ..........................................3-24
IIPRT08B_ Printer ..........................................................................................3-29
IIPRT10

▫

 Color Screen Printer (HP XL300) ....................................................3-30

IIPRT04 Color Video Copier ..................................................................................3-31
IIDMT03A DAT Tape Drive ...................................................................................3-32

Installation ....................................................................................................3-34

IIDOP04A and IIDOP05A Optical Disk Drive .........................................................3-35
IIVTE0_ Video Terminal........................................................................................3-36
IICDD01 CD-ROM Drive.......................................................................................3-37

ETHERNET PROTOCOL .............................................................................................3-39

Содержание infi 90 40 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для infi 90 40 Series

CAB 4712 Operator'S Manual preview
4712
Бренд: CAB Страницы: 13
CAB 4712 Assembly Instructions Manual preview
4712
Бренд: CAB Страницы: 30
CAB 5314 Operator'S Manual preview
5314
Бренд: CAB Страницы: 17
CAB 3014 Service Manual preview
3014
Бренд: CAB Страницы: 33
C. Crane Camping Equipment Instruction Manual preview
Camping Equipment
Бренд: C. Crane Страницы: 8
C-Pro Direct ADM Fittings Manual preview
ADM
Бренд: C-Pro Direct Страницы: 4
C-Pro Direct ADM Instructions For Use preview
ADM
Бренд: C-Pro Direct Страницы: 4
iHealth PO3M Quick Start Manual preview
PO3M
Бренд: iHealth Страницы: 8
Yamaha Motif-Rack XS Code List preview
Motif-Rack XS
Бренд: Yamaha Страницы: 48
Zennio KLIC-DI Installation Notes preview
KLIC-DI
Бренд: Zennio Страницы: 3
Harken 3294 Instructions preview
3294
Бренд: Harken Страницы: 4
VelociRAX Light Bar Instruction Manual preview
Light Bar
Бренд: VelociRAX Страницы: 4
ABM Katana User Manual preview
Katana
Бренд: ABM Страницы: 17
Olympus EVIS EXERA III Instructions Manual preview
EVIS EXERA III
Бренд: Olympus Страницы: 130
GAPOSA M3A Reference Manual preview
M3A
Бренд: GAPOSA Страницы: 32
Petzl P51A Technical Notice preview
P51A
Бренд: Petzl Страницы: 15
Larson Electronics EPL-HB-150LED-RT-IBSC Instruction Manual preview
EPL-HB-150LED-RT-IBSC
Бренд: Larson Electronics Страницы: 2
ZAMST EK-1 Instructions For Use Manual preview
EK-1
Бренд: ZAMST Страницы: 14

Бренды по названию

Популярные бренды

Загрузить еще бренды