Bailey infi 90 40 Series Скачать руководство пользователя страница 101 | Manualshive

Страница: 101 / 132

background image

COMPONENT DESCRIPTION AND REPLACEMENT

POWER ENTRY PANEL

6 - 18

WBPEEUI220754A0

®

The MAIN POWER indicator is lit when the AC power is con-
nected to the power entry panel and the main power circuit
breaker is on.

The AC outlet marked SCSI PERIPHERAL

is a convenience out-

let for either 120 or 240-VAC devices. Check the notice on the
front of the power entry panel before connecting anything into
this outlet.

NOTES:
1.

Use the AC outlet for the intended purpose only.

2.

Refer to

for wiring and cable connections. Some of

the connections are on the back of the power entry panel and are
accessed through the door on the back of the OIS console or driver
cabinet.

Driver Cabinet Power Entry Panel

The power entry panel contains the incoming AC power termi-
nals and system circuit breakers along with ports for connect-
ing peripheral devices and a system reset switch. Refer to
Table

for the power entry panel part numbers.

The power entry panel for the OIS driver cabinet also contains
a floppy disk drive and floppy controller board and a support
tray for an IIDMT03A tape drive. Refer to Figure

to view the

power entry panel.

The SCSI PERIPHERAL

port connection is for a IIDMT03A DAT

tape drive (tabletop unit) used for rapid reloading of system
and user configuration files for the OIS console.

The SYSTEM RESET pushbutton resets the OIS multibus
cards to an initial power up condition when pressed.

The MAIN POWER indicator is lit when the AC power is con-
nected to the power entry panel and the main power circuit
breaker is on.

The AC outlets marked AC OUTLETS are convenience outlets
for either 120 or 240-VAC devices.

NOTES:
1.

Use the AC outlets for the intended purpose only. Check to

make certain the peripheral device has the same power require-
ments.

2.

Refer to

for wiring and cable connections. Some of

the connections are on the back of the power entry panel and are
accessed through the door on the back of the OIS console or driver
cabinet.

«
...
99
100
101
102
103
...
»

Содержание infi 90 40 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для infi 90 40 Series

Бренд: T-Drill Страницы: 75

Бренд: Zeiss Страницы: 38

Pro Vantage 12+ Series

Бренд: Ecco Страницы: 6

Бренд: Garmin Страницы: 20

Бренд: M-Audio Страницы: 48

Бренд: M-Audio Страницы: 19

Бренд: M-Audio Страницы: 17

Бренд: M-Audio Страницы: 18

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 20

Бренд: Cannon Страницы: 70

Бренд: Sakai Страницы: 31

Бренд: Ultrasonic Страницы: 33

Бренд: Fillauer Страницы: 12

Бренд: lumishore Страницы: 13

Бренд: Datavideo Страницы: 4

Бренд: Amadas Страницы: 111

Бренд: Tascam Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды