Bailey infi 90 40 Series Скачать руководство пользователя страница 44 | Manualshive

Страница: 44 / 132

background image

INSTALLATION

OPERATOR INTERFACE DEVICES

WBPEEUI220754A0

3 - 19

Up to four annunciator display panels can be driven from an
MKM module. Maximum cable length is 4.5 meters (15 feet).
Refer to the

Operation

and

Configuration

instructions

(Table

) for more information.

Touch Screen

A touch screen accessory provides a means of selecting display
options by touching the desired area on the monitor screen. Up
to two touch screen controller cards can be mounted onto the
IIMKM02A module. The first touch screen controller card
mounts onto the component side of the MKM module. The sec-
ond touch screen controller card is identical to the first and
mounts onto the solder side of MKM module. The touch screen
card interprets signals from the touch screen monitor overlay
and sends them to the MKM board. This accessory can be used
on all console models and is ordered by nomenclature (Table

). One touch screen may be installed per color monitor. This

accessory requires the addition of a touch screen and touch
screen controller card.

CONTROLLER CARD INSTALLATION

Figure

shows the wiring connections. Figure

the dipswitch settings and jumper positions of the touch
screen controller card and the jumpers on the IIMKM02A
board. Before attaching the touch screen ribbon cable to the
controller board, ground the capacitive charge on the touch
screen to the monitor case ground:

1. Insert one end of a 24-AWG wire into either outside touch
screen cable connector contact.

2. Press the other end of the wire to the monitor case ground.

NOTE: Failure to perform this may damage the electronic compo-
nents on the controller by the stored charge from the 25 kV anode
during picture tube operation.

Table 3-3. IIADP01 Board Connections for Multiple ADPs

Cable

Number

Connect From

Connect To

1948978

_

1

P1 or P2 on ADP 2

AUX 1 port on keyboard interface
panel or to P1 or P2 on ADP 3 board

Table 3-4. Touch Screen Nomenclature

Nomenclature

Description

AOHOIS42TS1

IIOIS42X1 single lower console

AOHOIS42TS2

IIOIS42X2 upper monitor

AOHOIS42TS3

IIOIS42X3 Dual monitor

«
...
42
43
44
45
46
...
»

Содержание infi 90 40 Series





































































































































Отзывы:

Нет отзывов

Похожие инструкции для infi 90 40 Series

Бренд: Fein Страницы: 248

Бренд: ZF Страницы: 30

Бренд: Raymarine Страницы: 111

Бренд: OfiTE Страницы: 21

Бренд: Earthlite Страницы: 4

Бренд: YATEK Страницы: 78

Бренд: FJC Страницы: 2

Бренд: OMCA Страницы: 36

Бренд: Salford Страницы: 64

Бренд: Tascam Страницы: 27

Бренд: Jay-Lor Страницы: 72

Бренд: MacDon Страницы: 198

Бренд: M-Triangel Страницы: 6

Бренд: Facsimile Страницы: 16

Бренд: Cambridge Audio Страницы: 2

Бренд: Quanser Страницы: 12

Бренд: Daga Страницы: 24

Бренд: DAF Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды