Baileigh TS-1040C Скачать руководство пользователя страница 68 | Manualshive

Страница: 68 / 84

background image

65

65

TROUBLESHOOTING

Symptom

Possible Cause

Possible Solution

Motor does not
start.

1. Switch disabling key removed.
2. Motor connection wired incorrectly.
3. Break or short in wiring; or loose
connections.
4. Power supply switched off or has
incorrect voltage.
5. Start capacitor has blown.
6. Centrifugal switch at fault.

1. Install switch disabling key.
2. Wire motor correctly (refer to inside
junction box cover or manual).
3. Trace/replace broken or corroded wires;
fix loose connections.
4. Switch power supply on/verify voltage.
5. Test/replace if at fault.
6. Adjust/replace centrifugal switch.

Machine stalls or
is underpowered.

1. Feed rate/cutting speed too fast.
2. Workpiece material unsuitable for
machine.
3. Workpiece crooked; fence
misadjusted.
4. Machine undersized for task.
5. Run capacitor at fault.
6. Belt slipping.
7. Motor wired incorrectly.
8. Plug/receptacle at fault.
9. Pulley/sprocket slipping on shaft.
10. Motor bearings at fault.
11. Contactor not energized/has poor
contacts.
12. Motor overheated.
13. Motor at fault.

1. Decrease feed rate/cutting speed.
2. Only cut wood/ensure moisture is below
20%.
3. Straighten or replace workpiece/adjust
fence.
4. Use correct blade/reduce feed rate or
depth of cut.
5. Test/repair/replace.
6. Tension/replace belt
7. Wire motor correctly.
8. Test for good contacts/correct wiring.
9. Replace loose pulley/shaft.
10. Test/repair/replace.
11. Test all legs for power/replace if faulty.
12. Clean motor, let cool, and reduce
workload.
13. Test/repair/replace.

Handwheel binds
or is difficult to
move.

1. Lock knob is engaged.
2. Handwheel shaft pins are wedged.

1. Loosen lock knob.
2. Remove handwheel and adjust shaft pins.

Blade does not
reach 90 degrees.

1. Pointer or scale calibrated
incorrectly.
2. 90 Degree stop bolt is out of
adjustment.

1. Calibrate pointer/scale at true 90 degrees.
2. Adjust 90 degree stop bolt.

Blade too close to
insert.

1. Blade position on arbor is incorrect.
2. Table mounting position is not
centered.

1. Verify that blade arbor washers are
correct and in the required position.
2. Loosen table mounting bolts, adjust table
position, then realign the blade.

WARNING:

Disconnect machine from the power source before attempting

any troubleshooting

«
...
66
67
68
69
70
...
»

Содержание TS-1040C





















































































Отзывы:

Нет отзывов

Похожие инструкции для TS-1040C

Бренд: Femi Страницы: 52

Бренд: Meister Страницы: 184

Бренд: Kalamazoo Страницы: 6

Бренд: Parkside Страницы: 74

Бренд: Far Tools Страницы: 16

Бренд: Diamond Products Страницы: 44

Бренд: XPOtool Страницы: 10

Бренд: stayer Страницы: 16

Бренд: Scheppach Страницы: 40

BROSZIO BUZZSAW D42

Бренд: Passat Страницы: 94

Бренд: Felder Страницы: 48

Precisa 4.0 Series

Бренд: Scheppach Страницы: 96

Бренд: Scheppach Страницы: 168

Бренд: Greenlee Страницы: 18

Бренд: Greenlee Страницы: 28

Бренд: FLORABEST Страницы: 57

Бренд: WilTec Страницы: 10

Бренд: Defort Страницы: 29

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды