Baileigh TS-1040C Скачать руководство пользователя страница 56

Страница: 56 / 84

ADJUSTMENT

Before operation, the machine should be carefully adjusted for best performance.

Adjusting the 45° & 90° Bevel Stops

1. Disconnect and lockout power to the saw!

2. Raise the blade to its highest position and lift the blade

guard.

3. Loosen the bevel lock knob and turn the blade tilting

handwheel clockwise until it stops.

4. Verify the angle of the blade with a combination square

from the left side of the blade; keep the square flat against
the table and against the flat part of the blade. Do not
touch the teeth or the table insert.

5. If the blade angle is incorrect, turn the 90° (A) stop screw

located on the table top to the left of the blade one full
counter-clockwise turn using the supplied 6 mm allen key.

6. Turn the hand wheel until the blade is at 90° to the table

surface. Then re-tighten the 90° stop screw clockwise until
slight resistance is felt. Do not over tighten stop screw.

7. Verify the 45° setting by tilting the blade as far as possible

to the left and using the square, check the angle and if
needed adjust as for the 90° stop, this time using the right
stop screw (B).

WARNING:

Make sure the electrical disconnect is OFF before working on

the machine.
Always follow proper safety precautions when working on or around any machinery.

Содержание TS-1040C





















































































Результаты поиска

Содержание TS-1040C

Отзывы:

Похожие инструкции для TS-1040C

Бренды по названию

Популярные бренды

Baileigh TS-1040C, Руководство оператора

Результаты поиска

Содержание TS-1040C

Отзывы:

Похожие инструкции для TS-1040C

Бренды по названию

Популярные бренды