Bacharach Fyrite INSIGHT Скачать руководство пользователя

Страница: 50 / 76

Fyrite INSIGHT

2. Allow the analyzer to cycle through its 60 second warm-up period.

During warm-up, the analyzer’s operation is checked and the sen-

sors are set to the following ambient conditions:

•

Oxygen sensor spanned to 20.9%

•

CO sensor zeroed

•

Pressure sensor zeroed

Any errors detected during warm-up will be listed on the display

immediately following warm-up, as displayed below.

Correct any errors before proceeding. Refer to Section 6.7 for a

list of error messages and their meanings.

3. Press the

MENU (F2)

button to access the Main Menu.

4. Use the ▲▼ buttons to select Calibration. Press

ENTER

to dis-

play the Calibration Password screen.

5. Before calibration can begin a 4-place numeric password must be

entered. Use the ▲▼ and ◄► buttons to enter the password.

(Note that the default password is 1111)

6. Press the

ENTER

button to accept the password. If the correct

password was entered, the Calibration Menu will be displayed.

7. Use the ▲▼ buttons to select the desired sensor channel to be

calibrated, and then perform the calibration procedure for that

sensor as described in the following sections.

Содержание Fyrite INSIGHT













































































Результаты поиска

Содержание Fyrite INSIGHT

Отзывы:

Похожие инструкции для Fyrite INSIGHT

Бренды по названию

Популярные бренды

Bacharach Fyrite INSIGHT, Инструкция по эксплуатации

Результаты поиска

Содержание Fyrite INSIGHT

Отзывы:

Похожие инструкции для Fyrite INSIGHT

Бренды по названию

Популярные бренды