Bacharach Fyrite INSIGHT Скачать руководство пользователя страница 49

Страница: 49 / 76

Fyrite INSIGHT

5.0 CAlIBRATION & MAINTENANCE

IMPORTANT:

Before performing any calibration procedure,

ensure that fresh batteries are installed or use the optional

AC power adapter. Also, ensure that the analyzer is at room

temperature and will be sampling fresh air when powered

ON.

IMPORTANT:

To maintain accuracy as listed in the Techni

cal Characteristics Section of this manual, the standards

used must be at least four times as accurate as the stated

accuracy of the Fyrite

INSIGHT.

5.1 B-Smart

™

Sensors

The Fyrite

INSIGHT utilizes Bacharach’s new B-Smart

™

Sensor tech-

nology for its CO sensor. The B-Smart

™

sensor is marked with a 10-digit

calibration code that can be entered in the instrument’s memory via the

keypad, or with Fyrite user software.

Benefits of B-Smart

™

Sensors:

•

New sensors can be installed without applying gas for calibration.

•

Sensors can be pre-calibrated and installed when needed.

•

Sensors can be moved from one analyzer to another.

The B-Smart

™

sensors should be calibrated by an authorized Bacharach

Service Center every 6 to 12 months to assure that the analyzer contin-

ues to meet its published accuracy specifications. The B-Smart

™

sensors,

however, can be calibrated in the field if your facility has the necessary

equipment and qualified personnel to perform the procedures described in

the following sections of this instruction manual.

5.2 Starting a Calibration

Start any calibration by performing the following:

1. With the analyzer power off, place the unit in fresh, ambient air;

then power on the analyzer.

Содержание Fyrite INSIGHT













































































Результаты поиска

Содержание Fyrite INSIGHT

Отзывы:

Бренды по названию

Популярные бренды

Bacharach Fyrite INSIGHT, Инструкция по эксплуатации

Результаты поиска

Содержание Fyrite INSIGHT

Отзывы:

Бренды по названию

Популярные бренды