Automatismos Pujol SPIDER PRO 600, Инструкция по установке и настройке

Страница: 20 / 28

automatismos pujol -
2
- english
SPIDER PRO 600
GENERal INfORmaTION
This product complies with the “safety, specific rules for powering vertically opening garage doors in residential use” standard (standard EN 60335-
2.95). This product, which is installed in accordance with this guide and the «installation verification sheet», complies with the EN 13241-1 and EN
12453 standards.
The instructions referred to in the product’s installation guide and instructions for use are designed to prevent damage to property and personal injury
along with compliance with the above standards. Failure to comply with these instructions absolves automatismos pujol of any liability resulting from
damage that may be caused. The Spider Pro 600 product must be installed inside the garage with an integrated emergency control system.
automatismos pujol declares that this product complies with the essential requirements and other relevant provisions of Directive 1999/5/EC. A
Declaration of Conformity is available at www.somfy.com/ce (Dexxo Compact RTS).
Product can be used in the European Union, Switzerland and Norway.
SafETy INSTRuCTIONS
Caution
Important safety instructions. Follow all the instructions as incorrect installation can lead to serious injury.
Safety instructions
Before installing the motorisation, remove any unnecessary cords or chains and switch off all equipment which is not required for the motorised door
to function.
Before installing the motorisation, ensure that the driven part is in good mechanical condition, that it is correctly balanced and that it opens and
closes correctly.
Position all control buttons at least 1.5 m from the ground, visible from the entrance but far enough away from the mobile parts.
Position the manual back release device a maximum of 1.8 m from the ground.
In the case of a removable mobile component, it is recommended to store it in the immediate proximity of the door.
Permanently affix the label concerning the manual repair device near to its mobile component.
Permanently affix the crushing warning labels near to any fixed control devices, and so that they are extremely visible to the user.
After installation, check that the mechanism is correctly configured and that the motorisation changes direction when the door encounters an
obstacle on the ground which is 50 mm high.
After installation, ensure that none of the door components overhang the top of a pavement or public road.
After installation, check that the motorisation prevents or stops the opening movement when the door is bearing a 20 kg weight, attached to the
middle of the lower edge of the door.
PRODuCT DESCRIPTION
Composition
fig. 1
No. Number Description No. Number Description
1 1 Motor head 13 2 TH M8x16 zn screws
2 1 Flap 14 6 HU8 nut
3 1 Lintel yoke 15 2 Shaft
4 1 Door yoke 16 2 Circlips
5 2 Ceiling mounting bracket 17 4 Thread-forming screws Ø 4x8
6 2 Motor head mounting bracket 18a 1 Single unit rail
7 1 Manual back release device 18b 1 2-part rail
8 1 Connecting arm 18b1 1 Sleeve
9 1 End limit stop 18b2 8 Thread-forming screws Ø 4x8
10 2 TCB-H 4.2x13 zn self-tapping screws 19 1 or 2 Vario Secure remote control
11 1 Power supply cord 20 1 24V 21W bulb type BA15s
12 4 TH10 M8x12 zn washer screws 21 2 Chain bearings
area of application
fig. 2
Types of door (fig.2)
A : overhead door.
B : sectional door:
- if the upper profile of the panel is special, use the «mounting yoke for a sectional door”.
Door dimensions (fig. 2)
Garage doors up to a surface area of 7 m² can be motorised.
For doors which are maximum in height, the motor travel can be optimised:
• By mounting the motor head at 90° (Fig. 6-
).
• By fixing the lintel yoke to the ceiling, setting it back a maximum of 200 mm in relation to the lintel (Fig. 4- )
• By cutting the connecting arm.
https://appceso.com