Automationdirect.com DL305 Скачать руководство пользователя страница 53

Страница: 53 / 200

3--

ola

3--15

F3--04ADS 4-Channel Isolated Analog Input

The following instructions are required to scale the data. We’ll continue to use the

42.9 PSI example. In this example we’re using channel 1. Input 114 is the active

channel indicator for channel 1. Of course, if you were using a different channel, you

would use the active channel indicator point that corresponds to the channel you

were using.

114

DSTR

R400

F50

DIV

K4096

F74

This instruction brings the analog value (in BCD)

into the accumulator.

This instruction moves the two-byte decimal

portion into the accumulator for further operations.

Scale the data

The analog value is divided by the resolution of the

module, which is 4096. (1760 / 4096 = 0.4296)

DSTR

R576

F50

MUL

K100

F73

DSTR

R576

F50

DOUT

R450

F60

Accumulator

Aux. Accumulator

Accumulator

Aux. Accumulator

This example assumes you have already read the analog data

and stored the BCD equivalent in R400 and R401

Accumulator

Aux. Accumulator

The accumulator is then multiplied by the scaling

factor, which is 100. (100 x 4296 = 429600). Notice

the most significant digits are now stored in the

auxilliary accumulator. (This is different from the

way the Divide instruction operates.)

Accumulator

Aux. Accumulator

R577

R576

R577

R576

R577

R576

R577

R576

This instruction moves the two-byte auxilliary

accumulator for further operations.

Accumulator

Aux. Accumulator

R577

R576

This instruction stores the accumulator to R450.

R450 now contains the PSI, which is 42 PSI.

Accumulator

Store in R451 & R450

R451

R450

Содержание DL305









































































































































































































Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды

Automationdirect.com DL305, Руководство пользователя

Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды