Automationdirect.com DL305 Скачать руководство пользователя страница 167

Страница: 167 / 200

3--

10--3

F3--08TEMP 8-Channel Temperature Input

The following table provides the specifications for input temperature probes

compatible with this module.

Compatible Temperature Probe Specifications

Transmitter Type

AD590

Input Temperature Range

--40

to 212

F (--40

to 100

C) --

(Opto 22 PN ICTD)

--67

to 302

F (--55

to 150

C) --

(Analog Devices PN AC2626J)

Transmitter Output

for Opto 22 and

Analog Devices

A /

K, 298.2

A @ 25

218

A @ --55

C, 423

A @ 150

The F3--08TEMP Temperature Input appears as a 16-point module. The module can

be installed in any slot configured for 16 points. See the DL305 User Manual for

details on using 16 point modules in DL305 systems. The limitation on the number of

analog modules are:

For local and expansion systems, the available power budget and

16-point module usage are the limiting factors.

Compatible

Temperature Probe

Specifications

Analog Input

Configuration

Requirements

Содержание DL305









































































































































































































Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды

Automationdirect.com DL305, Руководство пользователя

Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды