Automationdirect.com DL305 Скачать руководство пользователя страница 149

Страница: 149 / 200

3--

--n

ple

9--3

F3--08THM--n 8-Channel Thermocouple Input

Module Specifications

The following table provides the specifications for the F3--08THM--n Thermocouple

Input Module from FACTS Engineering. Review these specifications to make sure

the module meets your application requirements.

Number of Channels

8, differential inputs

Input Ranges

Type E: --270/1000

C, --450/1832

Type J: --210/760

C, --350/1390

Type K: --270/1370

C, --450/2500

Type R: 0/1768

C, --32/3214

Type S: 0/1768

C, --32/3214

Type T: --270/400

C, --450/752

--1: 0 -- 50 mV
--2: 0--100 mV

Resolution

12 bit (1 in 4096)

Input Impedance

27K

Absolute Maximum Ratings

Fault protected input, 130 Vrms or 100 VDC

Cold Junction Compensation

Automatic

Conversion Time

15ms per channel, minimum

1 channel per CPU scan

Converter Type

Successive Approximation, 574

Linearity Error

1 count (0.03% of full scale) maximum

Maximum Inaccuracy at 77

(25

0.35% of full scale

Accuracy vs. Temperature

57 ppm /

C maximum full scale

Power Budget Requirement

50 mA @ 9 VDC, 34 mA @ 24 VDC

External Power Supply

None required

Operating Temperature

to 140

F (0

to 60

Storage Temperature

--4

to 158

F (--20

to 70

Relative Humidity

5 to 95% (non-condensing)

Environmental air

No corrosive gases permitted

Vibration

MIL STD 810C 514.2

Shock

MIL STD 810C 516.2

Noise Immunity

NEMA ICS3--304

The F3--08THM--n Thermocouple Input appears as a 16-point module. The module

can be installed in any slot configured for 16 points. See the DL305 User Manual for

details on using 16 point modules in DL305 systems. The limitation on the number of

analog modules are:

For local and expansion systems, the available power budget and

16-point module usage are the limiting factors.

Analog Input

Configuration

Requirements

Содержание DL305









































































































































































































Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды

Automationdirect.com DL305, Руководство пользователя

Результаты поиска

Содержание DL305

Отзывы:

Похожие инструкции для DL305

Бренды по названию

Популярные бренды