Automationdirect.com DL305 Скачать руководство пользователя страница 193

Страница: 193 / 200

A--12

DL305 Data Types and Memory Map

System

V-memory

Description of Contents

V7751

Fault Message Error Code — stores the 4-digit code used with the FAULT instruction when the

instruction is executed.

V7752

Reserved

V7753

Reserved

V7754

Reserved

V7755

Error code — stores the fatal error code.

V7756

Error code — stores the major error code.

V7757

Error code — stores the minor error code.

V7760--V7762 Reserved
V7763--V7764 Location for syntax error information.
V7765

Scan — stores the total number of scan cycles that have occurred since the last Program Mode to Run

Mode transition.

V7766

Contains the number of seconds on the clock. (00 to 59).

V7767

Contains the number of minutes on the clock. (00 to 59).

V7770

Contains the number of hours on the clock. (00 to 23).

V7771

Contains the day of the week. (Mon, Tue, etc.)

V7772

Contains the day of the month (1st, 2nd, etc.).

V7773

Contains the month. (01 to 12)

V7774

Contains the year. (00 to 99)

V7775

Scan — stores the current scan time (milliseconds).

V7776

Scan — stores the minimum scan time that has occurred since the last Program Mode to Run Mode

transition (milliseconds).

V7777

Scan — stores the maximum scan time that has occurred since the last Program Mode to Run Mode

transition (milliseconds).

DL350 Comm Port 2 Control Relays

The following system control relays are valid only for D3--350 CPU remote I/O setup

on Communications Port 2.

System CRs

Description of Contents

C740

Completion of setups -- ladder logic must turn this relay on when it has finished writing to

the Remote I/O setup table

C741

Erase received data -- turning on this flag will erase the received data during a communica-

tion error.

C743

Re-start -- Turning on this relay will resume after a communications hang-up on an error.

C750 to C757 Setup Error -- The corresponding relay will be ON if the setup table contains an error (C750

= master, C751 = slave 1... C757=slave 7

C760 to C767 Communications Ready -- The corresponding relay will be ON if the setup table data is valid

(C760 = master, C761 = slave 1... C767=slave 7

Содержание DL305









































































































































































































Результаты поиска

Содержание DL305

Отзывы:

Бренды по названию

Популярные бренды

Automationdirect.com DL305, Руководство пользователя

Результаты поиска

Содержание DL305

Отзывы:

Бренды по названию

Популярные бренды