Automated Logic RC642 Скачать руководство пользователя страница 80

Страница: 80 / 94

Zone setpoint adjust

The occupant can adjust the heating and cooling setpoints at the zone sensor.

Zone unoccupied override

The occupant can press a button to override the schedule and place the unit in occupied

mode for 30 minutes. Each additional press of the button adds 30 minutes, to a

maximum of 90 minutes. When the override time ends, the schedule controls the unit

again.

Discharge temperature limit control (optional)

The unit monitors the discharge temperature and limits the heating or cooling outputs as

follows:

Mode

Discharge

Temperature

Capacity Limit

Heating

110°F (43°C)

100°F (38°C)

100%

Cooling

48°F (9°C)

100%

40°F (4.5°C)

Freeze protection (optional)

The unit shuts down when it receives a freezestat status.

Smoke detection (optional)

The unit shuts down when it receives a smoke detector status.

Fan

The fan runs any time the unit is providing heating or cooling. The timed local override

control will override this fan control, forcing the fan to run for the duration of the override

time (optional). To ensure the coils are not active when there is no airflow, the fan starts 1

minute before heating or cooling is enabled and runs for 5 minutes after heating or

cooling turns off.

Fan status (optional)

The Room Controller monitors the fan status. It requires a positive fan status before

enabling any heating or cooling stages.

Cooling

If staged cooling is used, the Room Controller measures the zone temperature and turns

on the first and second stage cooling (if available) as needed to maintain the cooling

setpoint. A 5-minute delay between stages prevents short cycling, and each stage has a 2-

minute minimum on time and a 4-minute minimum off time.
If chilled water is used, the Room Controller measures the zone temperature and

modulates the chilled water valve to maintain the cooling setpoint.
The cooling analog output opens to 50% when the freezestat is on.

Содержание RC642































































































Результаты поиска

Содержание RC642

Отзывы:

Бренды по названию

Популярные бренды

Automated Logic RC642, Технические инструкции

Результаты поиска

Содержание RC642

Отзывы:

Бренды по названию

Популярные бренды