background image

 
 

 

I

NSTALLATION 

C

HECK 

O

FF 

S

HEET

 

 

UL 325 COMPLIANT VPL-24 

 

      INSTALLATION CHECK OFF LIST 

THIS GATE OPERATOR IS INSTALLED FOR USE AS A CLASS ______ 

INSTALLATION. 

EACH ITEM ON THIS INSTALLATION CHECKOFF LIST 

MUST

 BE DISCUSSED 

WITH THE CUSTOMER.  A COPY SIGNED BY BOTH THE INSTALLER AND 

CUSTOMER 

MUST

 BE RETURNED TO AUTOGATE.  SIGNATURES INDICATE 

UNDERSTANDING OFF ALL SAFETY ASPECTS LISTED BELOW. 

 

____ FOUR WARNING SIGNS SECURELY INSTALLED ON EACH SIDE OF GATE PANEL.  

         (REQUIRED) 

____ 1 OR 2 SAFETY/REVERSING  PHOTO BEAMS INSTALLED, ONE ACROSS EACH SIDE OF 

GATE OPENING. 

____ TWO 12 VDC BATTERIES INSTALLED (REQUIRED) DEEP CYCLE MARINE RECOMMENDED. 
____ CUSTOMER ADVISED THAT GATE IS FOR VEHICULAR TRAFFIC ONLY. (REQUIRED) 
____ A SEPARATE PEDESTRIAN ENTRY AND/OR EXIT IS PROVIDED. (REQUIRED) 
____ GATE GUARD INSTALLED ON BACK SIDE OF OPERATOR. (REQUIRED) 
____ KICK PLATE INSTALLED ON DOOR SIDE OF OPERATOR. (REQUIRED) 
____ ARE ALL ACTUATING CONTROLS LOCATED FAR OUT OF REACH OF GATE. (REQUIRED) 
____ IS THIS CLASS OPERATOR APPROVED FOR THE APPLICATION OF THE OPERATOR  

(CLASS 1,2,3,4,) (REQUIRED) 

____ ARE CONTROLS TO RESET GATE AFTER OBSTRUCTED INSTALLED IN LINE OF 

SIGHT.(REQUIRED) 

____ HARD WIRED CONTACT SENSORS LOCATED & WIRED TO AVOID ANY MECHANICAL  

DAMAGE.  

          ____  FIELD WIRING SECURED TO AVOID PINCHING DAMAGE. 

____ CUSTOMER INSTRUCTED AND IS CLEAR ON PROPER USE OF GATE OPERATOR.  

(REQUIRED) 

____ CUSTOMER INSTRUCTED ON PROPER USE OF ALL CONTROL SEVICES USED WITH  

OPERATOR. 

____ SAFETY INSTRUCTIONS WERE REVIEWED AND LEFT WITH CUSTOMER. (REQUIRED) 
____ DID INSTALLER OFFER A PREVENTATIVE SERVICE / MAINTENANCE CONTRACT. 
____ A PHOTO OF COMPLETED INSTALLATION TAKEN FROM FRONT AND BACK OF GATE & 

DATED. 

____ CUSTOMER TRAINED ON MANUAL OPERATION OF THE GATE. 

 
 
       _____________________________ 

 

 

 

 

 

__________________ 

            CUSTOMER’S SIGNATURE     

 

 

 

 

 

 

 

DATE 

 
 
       _____________________________ 

  

 

 

 

 

__________________ 

            INSTALLER’S SIGNATURE   

 

 

 

 

 

 

            DATE 

 
CUSTOMER & INSTALLER MUST RETAIN A COPY OF THIS CHECK OFF LIST FOR THEIR RECORDS 

1.800.944.4283 AutoGate Technical Support 

 

Содержание VPL-24/UL















































Отзывы: