auer 751600 страница 3 Скачать руководство пользователя

Страница: 3 / 60

manual

HRC

PILOT -PREMIUM-

manual

HRC

PILOT -PREMIUM-

1.1 - Important information

1 - PLEASE READ

IMMEDIATELY

These installation and operating instructions form part of the

appliances which they refer to.

In order for the warranty to be valid, the operating

instructions must be read before using the

appliance.

This manual must be safeguarded and passed on to

any successive users for future reference.

It will be considered as evidence in case of litigation.

- Clean and flush the heating water circuit

before connecting any appliances (Heat

Pump and Pilot).
- The appliance only works when filled with

water. Never switch the appliance on unless it

has been properly filled and completely purged

of air.

- The filter valve ensures the protection of

the Heat Pump. An annual inspection of the

condition of the filter must be carried out.

- It is recommended to carry out periodic

inspections of the sludge levels and for

limescale and to clean if necessary. Always

switch off the appliance before cleaning.

- Always switch off the appliance before

undertaking any work on the electrical

components.

Caution: the fan blades will continue to spin

through inertia after the appliance is switched

off.

- Never get water on the control components or

electrical parts. Always switch off the appliance

before cleaning.

PLUMBING INSTALLATION

RECOMMENDATIONS

The high temperature Heat Pump absorbs the calories present in

exterior air, and transforms them into useful energy which is then

transferred to the heating water for your home. AUER cannot be

held responsible for any other usage of the appliance.
The safety advice and instructions contained in this document

must be strictly respected.
Before making any connections to the appliance, ensure that all of

the appliances are compatible with the installation.
Before switching on the appliance, check that the network

voltage to be applied to the appliance is the same as the one on

the rating plate of the appliance.
Before undertaking any manintenance work, handling, or in the

case of the appliance not functioning or malfunctioning, always

disconnect the appliance from the power supply and seek advice

from a technician or specialist.
AUER cannot be held liable for damages caused by not following

the instructions provided, nor any problems or errors caused

from improper handling, improper installation, or misuse of the

appliance.
The installation and operating instructions are subject to change

without prior notice.

1.2 - Safety advice and instructions

• This appliance should not be used by: children under 8 years old;

anyone with reduced physical, sensory or mental capabilities; or

by anyone who has insufficient experience or knowledge of the

appliance; unless they are being supervised by someone who is

responsible for their safety and in possession of the operating

instructions of the appliance.

• Use of the appliances when empty of water is

PROHIBITED

• Any work on the installation must be carried out by a qualified

professional with the appliance switched off.

• This appliance must be installed while respecting all local and

national electrical installation regulations.

Check that the installation is equipped with a propery sized and

properly connected ground cable.

This CE marked unit is in compliance with the following

standards:

- Low voltage 2006/95/CEE (standard EN 60.335.1)
- Electromagnetic compatibility 2004/108/CEE (standard EN

55014.1 / EN 55014.2).

1.3 - Delivery terms and conditions

In general, the material is transported at the recipient’s own risk.

It is important to verify that all of the elements have been

received and that no damage has been sustained during

transport upon receipt of the appliance and before beginning the

installation procedures.

Heat Pump

Accessories

Pilot

1.4 - Storage and transport

Admissible storage and transport temperatures are between

-20°C and +60°C.

1.4.1 - General information

The appliances must be stored and transported in their original

packaging, on a wooden pallet, in a vertical position and

completely empty of water.

Содержание 751600





























































Результаты поиска

Содержание 751600

Отзывы:

Похожие инструкции для 751600

Бренды по названию

Популярные бренды

auer 751600, Инструкция по установке и эксплуатации

Результаты поиска

Содержание 751600

Отзывы:

Похожие инструкции для 751600

Бренды по названию

Популярные бренды