background image

ADVANCED MANUAL / bit Ten D /

38

The 

bit Ten D

 software features a 31-band, ± 12 dB graphic 

equalizer for each system channel. 

In compliance with ISO requirements, frequencies are  

equally spaced at 1/3 Oct. from 20 to 20 kHz.

The equalizer works according to the functioning mode  

chosen. So we have:

    - one equalizer for the 

Front

.

    - one equalizer for the 

Rear

.

    - one equalizer for the 

Subwoofer

.

Eg.: 

 

 if examining the system described so far there would be:

    - one equalizer for the 

Front Mid-Tweeter

.

    - one equalizer for the 

Front Woofer

.

    - one equalizer for the 

Subwoofer

.

In order to set an equalization curve, you just have to select the channel 

you want to equalize from the 

Channel Map

 menu and left-click the 

slider you want to set with the mouse.

To shape an equalization curve, you just have to right-click the first 

slider on the left of the equalizer and move the equalizer sliders towards 

the right, shaping the curve as you like 

(see Fig. 1).

The graphic equalizer features five specific functions to ease 

adjustments 

(see Fig. 2)

.

  

1.

 

Select ALL 

once an equalization curve has been set, this  

        provides the ability to move all the cursors at the same time.

  

2

.

 Flat

, brings all the cursors back to the 0 dB position;

  

3.

 

EQ L/R Link

 when active, applies the equalization curve to 

        both the right and the left channel simultaneously.

  

4.

 

EQ Off

 

when active, provides the ability to disable the  

        equalizer to check its effect without losing its settings.

  

5.

 One 

Select

 button for each equalizable band, providing the  

        ability to move all the selected cursors all together.

Remark:

 in order to display more clearly the set equalization curve,  

the vertical axis (dB) can be increased or decreased by  

moving up/down the cursor on the right of the equalization  

curve graph 

(Fig. 3)

. By default the graph visualization range  

is set at ± 12dB

8.12

  GRAPHIC EQUALIZER

Fig.1

Fig.2

Fig.3

ZOOM 

-

ZOOM 

+

8

9

5

1

2

3

4

Example of visualization with magnifier function ± 3dB

Example of visualization with magnifier function ± 24dB

ZOOM

ZOOM

Содержание bit Ten D



















































Отзывы: