Audison bit Ten D Скачать руководство пользователя страница 20

Страница: 20 / 50

ADVANCED MANUAL / bit Ten D /

Turn the

bit Ten D

on.

Connect the USB cable to the appropriate port on the

bit Ten D

and to an available USB slot on the PC.

WARNING

When connecting a PC laptop via USB cable to the

bit Ten D

while the device is turned on, the laptop

has to work with its own battery and stay disconnected from the mains adapter (external power supply).

Once the connection between the PC laptop and the

bit Ten D

is established, you can immediately connect

the computer, if necessary, to the mains adapter.

Windows XP:

the PC will recognize the

bit Ten D

interface and will automatically install the driver;

Windows XP

Windows Vista:

the PC will recognize the

bit Ten D

interface and will automatically install the driver;

Windows Vista

Windows 7:

the PC will recognize the

bit Ten D

interface and will automatically install the driver;

Windows 7

The peripheral device has been installed correctly and is ready for use.

7.2

DRIVERS INSTALLATION GUIDE

Remark:

The

bit Ten D

uses HID drivers already integrated in Windows. For this reason, they are not included on the

CD and will always install automatically.

Windows XP

complete the installation procedure, then click

CLOSE

to exit the installation;

Windows Vista

: complete the installation procedure, then click

CLOSE

to exit the installation;

Windows 7

: complete the installation procedure, then click

CLOSE

to exit the installation:

Windows 8:

go on and complete the installation procedure, then click on

CLOSE

to exit the installation;

Содержание bit Ten D



















































Результаты поиска

Содержание bit Ten D

Отзывы:

Похожие инструкции для bit Ten D

Бренды по названию

Популярные бренды

Audison bit Ten D, Руководство для продвинутых пользователей

Результаты поиска

Содержание bit Ten D

Отзывы:

Похожие инструкции для bit Ten D

Бренды по названию

Популярные бренды