Audison bit Ten D Скачать руководство пользователя страница 22

Страница: 22 / 50

ADVANCED MANUAL / bit Ten D /

8. bit Ten D INSTALLATION GUIDE USING A PC.

To configure the

bit Ten D

inputs, analog (PRE) and digital (AD Link + AC Link) outputs, equalizations and time delays,

the processor must be connected to a PC after calibrating the input levels. At that point, you need to have in mind

the system you want to realize, since from this moment if you want to change any of the settings, you will have to go

through the guided procedure all over again.

More specifically the guided procedure will ask for:

What kinds of specialization the main inputs channels use. The guided procedure changes according to your selection.

Which auxiliary inputs will be used (e.g. AUX and PHONE or OPTICAL IN).

Which kind of signals will be allocated to the different outputs (e.g. Front Left, Center or Subwoofer etc.).

Which speakers you are using for your system (e.g. 2-way Front, Front / Rear, Sub etc.).

If the system features passive crossovers to manage speaker groups (e.g. 2-way system with active mid-low).

During this procedure, you should disconnect the

bit Ten D

output RCA plugs to the amplifiers.

Turn on the

bit Ten D

and connect the USB cable to a PC. After installing the

bit Ten D

software, start it by

clicking the icon previously created on the PC desktop.

The first screen shown is the start page where you need to choose among three operational modes:

Select the

Target

(1)

start mode on the drop-down menu, then double click

(2)

on the

bit Ten D

image or press

ENTER.

8.1

SELECTING THE MASTER (FRONT / REAR) INPUTS AND OUTPUTS - TARGET MODE

- TARGET:

bit Ten D setup

- OFFLINE bit Ten:

demo mode bit Ten (sel)

- OFFLINE bit Ten D:

demo mode bit Ten D (sel)

- RESCUE MODE:

Firmware upgrade

recovery (sel)

Connect the head unit speaker outputs to the bit Ten D high-level input

(see 4.2)

Before turning on the system, make sure the amplifier’s RCA plugs are disconnected from the bit Ten D

to avoid speaker damage during the calibration procedure

The input calibration procedure must be performed with the ignition turned on. In this case, the car voltage is about

14.0 volts. The head unit will provide an undistorted output signal at higher volume.

Make sure that the IN Level knobs for the inputs used (L / R Front, L / R Rear, Phone, Aux IN L-R) are set to

minimum sensitivity as in the figure (position -).

Содержание bit Ten D



















































Результаты поиска

Содержание bit Ten D

Отзывы:

Бренды по названию

Популярные бренды

Audison bit Ten D, Руководство для продвинутых пользователей

Результаты поиска

Содержание bit Ten D

Отзывы:

Бренды по названию

Популярные бренды