Version 5.6
305
November 2008
SIP User's Manual
4. ini File Configuration
Parameter
Description
LineBuildOut.Loss
For a description of this parameter, refer to “Configuring the Trunk
Settings” on page
.
ISDNRxOverlap_x
For a description of this parameter, refer to “Configuring the Trunk
Settings” on page
.
ISDNRxOverlap
[0]
= Disabled (default).
[1]
= Enabled.
Any number bigger than one = Number of digits to receive.
Notes:
If enabled, the device receives ISDN called number that is sent in
the 'Overlap' mode.
The INVITE to IP is sent only after the number (including 'Sending
Complete' Info Element) was fully received (in SETUP and/or
subsequent INFO Q.931 messages).
For detailed information on ISDN overlap dialing, refer to ISDN
Overlap Dialing on page
R2Category
For a description of this parameter, refer to “Configuring the Digital
Gateway Parameters” on page
.
CallPriorityMode
For a description of this parameter, refer to ''Supplementary Services''
on page
.
MLPPDefaultNamespace
For a description of this parameter, refer to “Configuring the Digital
Gateway Parameters” on page
.
SIPDefaultCallPriority
For a description of this parameter, refer to “Configuring the Digital
Gateway Parameters” on page
.
MLPPDiffserv
For a description of this parameter, refer to ''Supplementary Services''
on page
.
PreemptionToneDuration
For a description of this parameter, refer to “Configuring the Digital
Gateway Parameters” on page
.
MLPPNormalizedServiceD
omain
MLPP normalized service domain string. If the device receives an
MLPP ISDN incoming call, it uses the parameter (if different from
‘FFFFFF’) as a Service domain in the SIP Resource-Priority header in
outgoing INVITE messages. If the parameter is ‘FFFFFF’, the
Resource-Priority header is set to the MLPP Service Domain obtained
from the Precedence IE.
The valid value is a 6 hexadecimal digits. The default is ‘000000’.
Note:
This parameter is applicable only to device's using the MLPP
NI-2 ISDN variant with CallPriorityMode set to 1.
MLPPDefaultServiceDoma
in
MLPP default service domain string. If the device receives a non
MLPP ISDN incoming call (without a Precedence IE), it uses the
parameter as a Service domain in the SIP Resource-Priority header in
outgoing (Tel-to-IP calls) INVITE messages. This parameter is used in
conjunction with the parameter SipDefaultCallPriority.
The valid value is a 6 hexadecimal digits. The default is "000000".
Note:
This parameter is applicable only to device's using the MLPP
NI-2 ISDN variant with CallPriorityMode set to 1.
Содержание Mediant 2000
