21
W
W
o
o
r
r
k
k
i
i
n
n
g
g
w
w
i
i
t
t
h
h
t
t
h
h
e
e
l
l
a
a
w
w
n
n
a
a
e
e
r
r
a
a
t
t
o
o
r
r
Aerating
With the aerator drum (optional accessory, if applicable) the
device can be used as lawn aerator to remove grass and moss as
well as cutting through wild growth with low roots.
To enable the growth of a healthy lawn in spring, the absorption of
water, air and nutrients in the root area needs to be increased. We
recommend aerating the lawn, depending on the condition, every
6 – 8 weeks.
To achieve good results and to extent the life of the aerator drum,
the lawn should be mowed before aerating (approx. 2 cm).
•
Install the aerator drum (see “Assembly”)
•
Fight the moss with a commercially available agent before
aerating.
•
Proceed as described under “Scarifying”.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
a
a
n
n
d
d
c
c
l
l
e
e
a
a
n
n
i
i
n
n
g
g
Before each maintenance and cleaning work:
−
switch off device
−
wait until the drum is stationary
−
pull out main plug
Maintenance and cleaning activities beyond those described in this
chapter may only be performed by customer service.
For maintaining and cleaning, removed security devices must
unconditionally be mounted properly and proved again.
Use only original parts. Other parts can result in unexpected
damages and injuries.
To make sure that the device is in a safe condition regularly check
the device for apparent defects such as
−
loose fastening elements (nuts, bolts, screws),
−
catching bag for wear or damaged parts,
−
worn or damaged components.
M
M
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Blade replacement
Wear protective gloves when working with
the blades. Risk of injury!
Worn blades reduce the performance of the device and put
excessive strain on the motor. Therefore check the condition of the
blades before each use. If necessary, have the blades sharpened
by an expert or replaced by new ones.
The blades can be turned. To turn the blades, proceed as
follows:
Â
Remove the cylinder head screws (34) on the bearing
holder (33) using the supplied installation wrench (42).
Â
Remove the scarifier drum (29).
Â
Remove the hexagon nut (b) and remove the cover (c),
flange (d), blades (30) and the spacer rings (e) from the axle.
Â
Turn the blades or insert new ones and install the drum again in
the opposite sequence.
Replace worn or damaged blades only as a set to avoid
imbalances!
Â
Retighten the hexagonal nut and place the drum in the device.
C
C
l
l
e
e
a
a
n
n
i
i
n
n
g
g
L
Clean the device carefully after each use to ensure
faultless function to be maintained.
Wear protective gloves when working with
the blades. Risk of injury!
Clean the device immediately after finishing the work.
Empty and clean the grass catching bag if necessary.
Clean the bottom of the device and the scarifier or aerator
drum.
Clean the housing, especially the vent slots, from grass and dirt
stuck to it.
Remove the dirt with a cloth or brush.
Do not clean the machine with running water or high-pressure
cleaners.
Do not use solvents for the synthetic parts (petrol, alcohol, etc.)
as these can damage the synthetic parts.
T
T
r
r
a
a
n
n
s
s
p
p
o
o
r
r
t
t
Pull the mains plug prior to transport.
The drum can be damaged during transport, e.g. on hard ground,
even when the motor is switched off. Therefore set the work depth
of the drum to position 1 during transport.
S
S
t
t
o
o
r
r
a
a
g
g
e
e
Pull out main plug.
Store unused equipment in a dry, locked place out of the reach
of children.
In case of extended storage (e.g. during winter) ensure that the
device is protected against frost and corrosion.
Before extended storage, please observe the following to
increase the service life of the device and to ensure smooth
operation:
−
thoroughly clean the device
−
Treat metal parts after each use against corrosion using an
environmentally friendly biologically degradable spray oil.
L
Never use any grease!
To facilitate space-saving storage of the device, you
can fold down the handle hoop. For this, loosen the star
grips (6) so that the handle hoop (1) and the connecting
bars can be swung in.
Содержание VT 40 Z
