Atal AWP-C Скачать руководство пользователя страница 3

Страница: 3 / 82

Table of contents

INTRODUCTION ................................................................................................. 5

SAFETY PRECAUTIONS AND PROHIBITED HANDLING .................................. 7

INSTALLATION ................................................................................................... 8

Hardware installation .............................................................................. 8

Provisioning and first setup .................................................................. 10

FEATURES ....................................................................................................... 12

LCD display ......................................................................................... 12

Keyboard ............................................................................................. 14

WiFi Modes .......................................................................................... 15

Main page ............................................................................................ 15

MODELS OF WIFI SENSORS ........................................................................... 17

DEVICE SETUP ................................................................................................ 22

Conventions ......................................................................................... 22

General settings ................................................................................... 23

Measurements settings ........................................................................ 26

Channels settings ................................................................................ 27

Alarms settings .................................................................................... 30

Network settings .................................................................................. 32

Protocols settings ................................................................................. 36

Cloud protocol settings ......................................................................... 41

COMMUNICATION PROTOCOLS .................................................................... 45

Modbus TCP ........................................................................................ 45

Cloud protocol

– JSON ........................................................................ 48

JSON and XML via http server ............................................................. 52

TROUBLESHOOTING ....................................................................................... 55

Factory defaults ................................................................................... 55

Forgotten administrator password ........................................................ 56

How to determine device IP address .................................................... 56

How to use newly connected Digi probe............................................... 56

Error codes at channels ....................................................................... 56

Warning exclamation mark on LCD ...................................................... 58

Battery symbol at LCD or wrong device time ........................................ 59

Unable to power on device ................................................................... 59

Device is restarting continuously .......................................................... 59

Measurement accuracy issue ............................................................... 59

WiFi connection issues ........................................................................ 60

RECOMMENDATIONS FOR OPERATION AND MAINTENANCE .................... 61

Operation in application areas .............................................................. 61

Recommendations for calibration ......................................................... 62

Recommendations for regular checks .................................................. 62

IT security advices ............................................................................... 63

Содержание AWP-C



















































































Результаты поиска

Содержание AWP-C

Отзывы:

Atal AWP-C, Руководство пользователя, Страница: 3 / 82

Результаты поиска

Содержание AWP-C

Отзывы: