Atal AWP-C Скачать руководство пользователя страница 13

Страница: 13 / 82

Security enabled

This symbol is shown when device security is
enabled.

Configuration session

This symbol is shown when configuration session
is under progress. Only one configuration
session is possible at one moment. That means
setup from other places is blocked when
configuration session is started.

Cloud connection

Sending data via Cloud protocol is under
progress currently.

Acoustic active

Device acoustic is active now.

Acoustic mute

Device acoustic was muted by web (software) or
via keyboard.

RSSI indicator and mode

Device is at client mode and
connection attempt into WiFi network
is under progress.

Device is at client mode and
connected into WiFi network. RSSI
value is not available yet.

Connected into WiFi network. Signal
strength is poor (RSSI < -69 dBm).

Connected into WiFi network. Signal
strength is sufficient.

Connected into WiFi network. Signal
strength is good (RSSI > -59 dBm).

Device is at AP mode. No client is
connected.

Device is at AP mode. At least one
client is connected.

Содержание AWP-C



















































































Результаты поиска

Содержание AWP-C

Отзывы:

Atal AWP-C, Руководство пользователя, Страница: 13 / 82

Результаты поиска

Содержание AWP-C

Отзывы: