Asymtek DV-7000 Series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 60

background image

Maintenance and Service

33

Table 5-1 Recommended Maintenance Schedule

Maintenance Procedure

Recommended

Frequency

Instructions

Clean the Dispensing Cartridge.

Daily

See “

Cleaning the Pump

” in this section.

Prime the fluid pump.

Daily

See “

Priming the Pump

” in the

Operation

section.

Inspect for fluid leakage and other
abnormalities.

Daily See

the

Troubleshooting

section.

Cleaning the Pump

"

NOTE

The cleaning procedures assume that a syringe is presently connected to the pump.

WARNING!

Refer to the Material Safety Data Sheet (MSDS) for important information about
safety, handling, and disposal for all fluids and solvents. All fluids, solvents, and
contaminated materials must be disposed of according to local regulations. Wear
personal protective equipment (PPE) when performing this procedure to prevent
contact with caustic chemicals.

DV-7000

Tools and Materials Needed:

•

Cotton

Swabs

•

Appropriate Personal Protective Equipment

•

1/4-inch

Wrench

•

Seal Insertion Tool Set (P/N 197004)

•

Cleaning Kit (P/N VK-7000K)

•

Cleaning Solution (MSDS recommended)

•

Cartridge Fitting (P/N 42-0228)

•

Feed Tube (P/N 42-0014)

•

Syringe Fitting (P/N 42-0229)

To clean a DV-7000 Cartridge (see Figure 5-1):

1. Use the position controls to move the dispensing head to the front center of the dispensing area.

2. Perform a service shutdown as specified in the applicable dispensing system manual.

3. Open the dispensing system front doors/hatch and locate the pump on the dispensing head.

4. Disconnect the feed tube from the cartridge fitting.

5. Push the blue cartridge release lever back towards the valve bracket.

6. Pull the cartridge out of the pump by gently pulling down on the nozzle.

7. Using a 1/4-inch wrench, remove the cartridge fitting from the cartridge body.

8. Discard the cartridge fitting in accordance with MSDS recommendations.

9. While holding the cartridge body in one hand and the end of the feedscrew in the other, gently

pull the feedscrew out of the cartridge.

!

The thrust collar should remain attached to the feedscrew.

«
...
35
36
37
38
39
...
»

Содержание DV-7000 Series





























































Отзывы:

Нет отзывов

Похожие инструкции для DV-7000 Series

Бренд: Gardena Страницы: 11

Бренд: Wanner Engineering Страницы: 16

Бренд: A.O. Smith Страницы: 8

Evosta2 11/139 SAN V

Бренд: DAB Страницы: 31

Бренд: DAB Страницы: 19

Бренд: Lavor Страницы: 108

Бренд: ICON Страницы: 16

Бренд: Daewoo Страницы: 38

FIGHTER 2010 Series

Бренд: Nibe Страницы: 36

H Design Series

Бренд: Continental Hydraulics Страницы: 8

Sandpiper Signature Series

Бренд: Idex Страницы: 18

Бренд: Water Ace Страницы: 16

Бренд: Bock Water heaters Страницы: 56

FLOJET G57C Series

Бренд: ITT Страницы: 4

JUNG PUMPEN HEBEFIX EXTRA

Бренд: Pentair Страницы: 32

Бренд: American Water Heater Страницы: 60

Smart Cylinders MS13555030S

Бренд: Rinnai Страницы: 24

Бренд: SKF Страницы: 30

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды